9 does no select the next line - Samsung Prostar 816 Phone

If you have lines appearing on your phone and they don't ring you need to program lines to ring. This type of programming is done from a M7310 phone. Page 323 of this manual shows how to program this on a NorthStar MICS Ver 6 phone system.
http://pdf.textfiles.com/manuals/TELECOM-F-R/Nortel%20MICS%20System%20Installer%20Guide%206.1.pdf

Enter the programming mode : Feature **266344
Password:266344
You will have 4 programming buttons on your phone, normally the 2 top left and 2 top right of the 2 vertical rows.
top left = move up one level
lower left = back
top right = select
lower right = next
once you enter the programming mode press next to "Terminals and Sets"
press select
enter your extension number
press select
press next to "Line Access"
press select
press next to "Line Assignment"
press select
use the next key to go to the line you want and use the soft-key below the display to change it from "Appear" to "Appear and Ring"

The answer to the Caller ID question:
Depend on the type of system that the phone is connected to. Late model Partner ACS equipment will display Caller ID info between the first and second rings, provided that the telephone line is plugged into a module that supports Caller ID.

The answers for the other 2 questions are taken directly out of the Partner ACS Programming Guide which is available for free download at Avaya's website.

Ther answer to the incoming call line ringing question:
Again, depends on the system. For the Partner ACS:

1) Press FEATURE 00 at extension 10 or 11.
2) Enter the number of the extension to be programmed for Line Ringing.

The green lights next to the line or pool buttons show the current Line Ringing settings for all

lines or pools assigned to the extension. (If a line or pool is not assigned to a button, the green

light next to that button is off.) The following ringing options can be shown by the green light

next to the line or pool button:

? Immediate Ring - on steady

? Delayed Ring - flashes slowly
? No Ring - flutters quickly

3) Press the line or pool button until the button light shows the correct setting (the setting for the
currently selected line or pool also appears on the display).
4) Continue programming, or exit programming mode.

Line selection:

For incoming calls, the line selection (hunt sequence) is set by the local service provider). For outgoing calls....again....it depends on the system. For the Partner ACS:

1) Press FEAURE 00, SYSTEM PROG, SYSTEM PROG, CENTRAL PROG at extension 10 or 11.
2) Enter the number of the extension to be programmed for Automatic Line Selection.
3) Press **.
4) Press the line, pool, or INTERCOM buttons in the desired order. The valid entries for Automatic
Line Selection depend upon the type of extension:

? Key Extension: Outside system lines, Left Intercom (the factory setting)

? Pooled Extension: Pool 880 button 1, button 2, Left Intercom, Right Intercom (the factory

setting), Pools 881-883, individual lines

For each button pressed, a display similar to the following appears:

Automatic Line Selection

5) To exit Automatic Line Selection, press **.
6) Press CENTRAL PROG and enter a new extension number, or exit programming mode.

Changing line ringing and line selection are tasks that are normally reserved for the Administrator of the telephone system.

To change the number of rings enter Feature 983, if your system has 2 digit intercom #s your password is 120000 if your system has 3 digit intercom #s your password is 1020000. once you have entered the password you will see 3 selections you can make .use the three soft keys under the display and select AA (auto Attendant).
The 3 soft key selections GRTG, TABLE, and LINES
Press the LINES soft key
Enter the line number on the line you want to change ringing on and press OK
Press the TABLE soft key then the RINGS soft key
Press the CHNG soft key and enter in the amount of rings you wantand press OK
Press the NEXT key to go to the next line
Repeat the procedure for the remaining lines
Press Rls when finished

Click On Start Button
Click On Settings
Click On Connection Tab
Select Connections Icon
Select Add a New Modem Connection under My ISP Enter Connection Name = Aircel
Select Cellular Line (GPRS) from Modem drop down list
Click On Next
Access Point Name =
aircelgprs.po (Postpaid),
aircelgprs.pr (Prepaid) Click On Next
Leave User Name & Password fields Blank
Click On Finish
To Connect the GPRS
Click On Start Select Internet explorer and type the Address
http://google.com

IF NOT WORKING THEN CONTACT UR AIRCEL CUSTOMER CARE, BUT REMEMBER IT IS NOW PAID, CHARGES 0.50 PAISE FOR PER 3 MINUTES.
THANKS ALOT,
SANJEEV KUMAR,
CELL.NO:+919876388918

install the driver or update the version if it is already installed

Here is the manipulation to be done to remedy this.

To begin, open Windows Explorer and click the Tools /Folder Options /Display. Look in the list "Hidden files and folders" and check "Show hidden files and folders."

• Right click on the icon "My Computer" from desktop and then click Properties. Then click on Hardware then Device Manager.
• Right click on the line marked "Unknown Device" and click "Update Driver".
• Then in the wizard to update the hardware choose "No, not this time."
• Click "Next."
• Select "Install from a list or specific location (Advanced)".
• Click Next.
• Then click on "Do not search I will choose the driver to install".
• Choose from the list of hardware USB hub.
• Click Next.
• Click on "Disk".
• A window opens. Then click "Browse", go to C: /windows/inf and select usbstor.inf and click Open.
• The path of the selected driver will appear in the previous window. Click "OK". The driver will be installrd and you have a line called "Device USB Mass Storage".
• Choose from the list of hardware "Storage Volume".
• Click "Next."
• Click on "Disk".
• A window opens. Click "Browse", go to C: /windows/ inf and select volsnap.inf select and click "Open."
• Then the path of the selected driver will appear in the previous window. Click "OK". The driver will be installed and you have a line called "Generic Volume".

To change the number of rings enter Feature 983, if your system has 2 digit intercom #s your password is 120000 if your system has 3 digit intercom #s your password is 1020000. once you have entered the password you will see 3 selections you can make .use the three soft keys under the display and select AA (auto Attendant).
The 3 soft key selections GRTG, TABLE, and LINES
Press the LINES soft key
Enter the line number on the line you want to change ringing on (probably Line 1) and press OK
Press the TABLE soft key then the RINGS soft key
Press the CHNG soft key and enter in the amount of rings you wantand press OK
Press the NEXT key to go to the next line
Repeat the procedure for the remaining lines
Press Rls when finished

TRY THIS
click on start button go to control panel open printers and faxes select your printer name right click on it and go to properties click on advance tab now select print processor and select WINPRINT and then RAW
now click ok and try printing
if still does the same thing then goto control panel printers and faxes and then click on add a printer select ADD A LOCAL PRINTER now select existing potr and select usb 001 click next select the brand HP and then DESKJET 990c in the printer list click next give your printer name and select set as default now click next and finish the installation now try printing

Press "Menu", Select "Handset Setup", select "Select Base", and then on that Select Base screen, move the arrow next to "Auto" and press select. I have been told this should solve your problem.

Measure with a ruler the size of the form in inches that you are going to use .

Calculate the number of lines you have by relating it to the Line Density using the formula
Form Length = Form Size * Line Density
For example for 11 inch paper at 6 lpi = 11 * 6 = 66 Lines

You must disable the Printers Menu Lock before you can change any settings - (power on holding down SETUP)

Press SET UP button on the Control Panel.

Select the MENU Option on the Control Panel Display.

Select the NEXT Option on the Control Panel Display until PAPER is displayed.

Select the PAPER Option on the Control Panel Display by pressing the button directly beneath it.

Select the Desired Paper Path for the Form Length change - The different Paper Paths can be stepped through by using the NEXT Option on the Control Panel Display.

Select Paper Path by pressing the button directly beneath it.

Select FORMLEN by pressing the button directly beneath it.

Select LINES and then increase or decrease the value on the Control

Panel Display by using the two arrow buttons until the desired length in lines has been achieved.

Select the SET Option on the Control Panel Display by pressing the button directly beneath it.

Set the Printer back ON-LINE by pressing the ON-LINE button.

This will set the form length on the printer, see the support section of www.dascom.co.uk for more info

Get the file here:http://harrythompson.com/webjal.htm
install then run:

1. Select Start

2. Select Run

3. Type in %SYSTEMROOT%\system32\drivers\etc\

Select Ok

4. Double click "hosts" (no extention, just hosts)

Open it up in notepad

5. Remove any lines that contain idenupate.motorola.com (the entire line)

6. On the last line add


216.19.0.250 idenupdate.motorola.com

7. Select File

8. Select Save

9. Select File

10. Select Exit

11. Open Internet Explorer

12. go to this site
https://idenupdate.motorola.com

13. If you did the above steps correctly, you will see
1999valid11


14. Double click the lock in the bottom right corner of the Internet Explorer window

15. Select "Install Ceritificate"

16. Select Next, Next, Finish, Ok

17. Select Start

18. Select Run

19. Type in "regedit"

19.5. Select Ok

20. Expand HKEY_LOCAL_MACHINE

21. Expand Software

22. Expand Motorola

23. Select WebJAL

24. Double click "SITE_URL"

25. Put the following URL in the EDITABLE text box
https://idenupdate.motorola.com/webjal010102/index.cgi

26. Select Ok

27. Exit Registry Editor

28. Run WebJAL

29. Select Login

30. Enter anything in Username and Password

31. Select Ok