Question about Boating

1 Answer

1992 evinrude 60hp boat motor

I'm not shure if I'm in the wright place to ask about my problem with my 60 hr evinrude. I'm removing the eng from the foot I've got them split about 1/4 inch apart & the eng. want come apart any more is there something I need to remove still have I misted something

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 456 Answers

Have you disconnected gearshift rod ? 7/16th bolt under bottom carb

Posted on May 13, 2014

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Jim Fowler

  • 23 Answers

SOURCE: Can not lower the motor manually

There is a screw usally on the right side looking at back of motor use large screw driver loosen motor will come down I guess you have trim and tilt

Posted on Jun 19, 2009

fordexpert

  • 5692 Answers

SOURCE: 1975 75 hp evinrude water in lower unit

You could take off the lower unit and leave the boat home. All they need is the bottom. The propshaft seal can be cut from fishing line. There should be another seal on the shift assembly and a third on the powershaft. Some you could do, but the shop can pressure test before and replace only what you need. Then pressure test after the repair to verify it seals.

Posted on Jul 20, 2009

Anonymous

  • 1 Answer

SOURCE: 20 hp evinrude boat motor will not start

broke key off of ignition trying to jump over, can't find wire to keep motor running, will start, but not stay running cause wired to toggle switch. can u help, please thanks, wayne (20hp johnson/evinrude

Posted on Nov 08, 2009

agent91

Ned White

  • 2100 Answers

SOURCE: how to remove starter from 1983 30hp evinrude OMC

I just read up on the removal of your carb, It says to remove the flywheel to get more room, and then the carb, the left side bolt is harder to get to but it can be done. Only get 1/6 turn of the wrench, remove the fuel line, and be careful not to lose any throttle parts. Hope this helps.

Posted on Apr 15, 2010

Testimonial: "The main problem is NOT knowing how to remove the starter. Thanks in advance, Wayne"

rgall3285

ray gallant

  • 65477 Answers

SOURCE: How to replace impeller on evinrude 115

disconnect the lower unit from the power head . makeing sure where the shift rod position is . then you will be getting near the water pump impeller .if you get it wrong the shifting won't work

Posted on Apr 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will a 60hp evinrude electric tilt/trim work on my 48hp evinrude


yes it will. bigger to smaller is okay and not a GREAT deal of difference in weight.

Mar 13, 2018 | Boating

1 Answer

Removal of power tilt unit on 2007 evinrude 60hp for .repainting


Hello mark,
Remove Engine from Boat.
Loosen Swivel Tube At Top Of Mounting Bracket.
Remove all Ssecuring Bolts On Power Trim Body.
Disconnect Electric Cable.
Move transom Brackets Appart.
Remove Trim Unit.
Hope This Helps
Gordy

Nov 30, 2017 | Boating

1 Answer

What sparkplugs go in a 92 60hp twostroke evinrude


I'd ring your local dealer he should help or email evinrude direct?
good luck.........

Sep 17, 2015 | Boating

3 Answers

How do i replace the water pump in a 2005 150 hp evinrude outboard motor


Take the cowling off. Also drop the foot. There wil be a stainless linkage rod that runs the length of the motor that you will have undo to drop the foot. The water impeller will be inside a stainless casing that you will have to disassemble.

Aug 17, 2012 | Boating

2 Answers

What is the correct fuel/oil mix for evinrude 4hp ?


the proper mix is 50 to 1 or 16 oz to every 6 gallons,in my little boat I put 4 quarts in the 48 gal tank and its been running for 22 years,your running way to rich and your plug is probaly fouled,take it out clean it up/dump your fuel and mix it right,thats a great motor you got,I hunted with it for years,oh yeah when you get started run it till all the smoke is gone or you will have carb problems ,if you dont have them all ready,a little carb cleaner wont hurt but get it running first,or all that trash will foul you out,have a great trip bartriley1

Jan 04, 2009 | Boating

Not finding what you are looking for?
Boating Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Boating Experts

ray gallant
ray gallant

Level 3 Expert

65470 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

29791 Answers

Tom Chichester

Level 3 Expert

54964 Answers

Are you a Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...