CODE FOR F1 - Sharp AR 163 Copier

A E1-F1 or E1-F2 is a faulty touchpad.
FixYourBoard.com has replacements about for NLA ovens.

They come with a two year warranty.
Reach out to us at 512-355-1108 or [email protected]

Barbara, F1 E1 error is your washer doesn't think the drain pump is working properly.bad CCU or pump.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

have E1 and F1 error code fleshing and wate Sears PartsDirect

http://forum.appliancepartspros.com/washer-repair/443358-f1-e1-error-fault-code.html

Appliance Repair Forums

Error code F1E1 null ShopYourWay

Central Control Unit CCU Maytag MHW6000XW Washer

virtual machine - VNC send Ctrl+Alt+F1-F6 to server - Unix ...

unix.stackexchange.com/.../vnc-send-ctrlaltf1-f6-to-serv...

Stack ExchangeMar 15, 2012 - Hence I can switch to the TTY's if my CTRL + ALT + F1 - F6 ... As I understand it, you want to send CTRL-ALT-F3 to the remote .... What numeric keycodes do I need to send for the magic sysrq functionality in a VNC session?

error code f1 dishwasher model gldt696tss 00 KVM Switches

www.fixya.com > ... > error code f1 dishwasher model gldt696tss 00

KVM Switches error code f1 dishwasher model gldt696tss 00 questions and ... 6F 23 20 F1 01 = F2 46 B1 59 04 61 77 71 Telewest 00 = 75 4A 66 04 CF 7F 55 F3 ... ...96 F6 1F C4 01 = 6D EA BE 97 6A AA DA 71 NTL 54 01] 07/10/09 00 = F0 ...

kleenmaid f6 code KVM Switches Questions & Answers - Fixya

www.fixya.com > Forum > Tags > kleenmaid f6 code

KVM Switches kleenmaid f6 code questions and answers. ... 01 = C6 64 1D EF 47 5A 0E EF tellywest 00= B7 DE 73 DE 2F A4 F3 BO 01= FA 4B 82 4C ... ...in bradford area plz 5a 01 83 5D 12 B8 96 F6 1F C4 6D EA 8E 97 6A AA DA 71 Hope ..

For error code f1 on washing machine click the link below :---
http://repairhelpcenter.blogspot.com/2012/01/code-f1-on-cabrio-washer.html

----------Also one more help link:---http://technoanswers.blogspot.com/2012/01/cabrio-washer-shows-code-f1.html
-----------Thanks.

Whirlpool Range / Stove / Oven Fault Codes Failure Code Fault Code Description Solution 4 Digit Failure Codes (for 2 digit codes see below) F1 - E0 EEPROM communication error 1. Disconnect power for at least 30 seconds.
2. Re-apply power and observe for at least one minute.
3. If code re-appears, replace control board (also called ERC or clock).

Note: Applies to all F1-E... codes except F1-E3. F1 - E1 EEPROM checksum error F1 - E2 UL A/D error(s) F1 - E4 Model ID error F1 - E5 Calibration shifted F1 - E6 Latch signal mismatch error F1 - E9 Stack overflow F1 - E3 Wiring harness cavity size does not match previously stored value The "Cavity Size Select" jumpers in the wiring harness indicate a cavity size different from that which the control was previously configured for. Check the jumpers in the harness to make sure they agree with the actual oven size.

F1 E1, replace Electronic Range Control.

In other words, the controller board has failed.

You can hold down the start key when the F1 is displayed it will show a sub code. The service manual for that model shows only one F1 code which is an F1-06. That is a shifter motor trouble. That is the section after the exit that offsets the copies.

You can reset the code with the instructions below. If the error recurrs then chech the exit section shidter for proper movement. You may require an on site technician to remedy this issue.

To reset the error code:
Hit <clear> <interrupt> <0> <interrupt>
14 <start>

This code is in responce to a fault/failure in the lower keypad assembly. It is possible the keypad was bumped.

Maytag Gemini fault codes.
Fault code Suspect area Fault code Suspect area
F0 - 0 None
F1 - 1 Runaway cook upper oven
F1 - 2 Runaway cook lower oven
F1 - 3 Runaway clean upper oven
F1 - 4 Runaway clean lower oven
F1 - 5 Keypad cancel upper
F1 - 6 Keypad cancel lower
F1 - 7 Keypad disconnected
F1 - 8 Keypad shorted
F1 - 9 Slave

F1 is a Relay circuit failure . you have a bad relay PCB or wire connection.

to fix your F1 error
92028 RELAY PCB, 105 C