Sentry Fire Safe -  Safe - DS3607 Logo

Related Topics:

A
Anonymous Posted on Apr 19, 2014

I can't open my sentry safe CSW3607

Battery light blinks on low. Safe wont open when I enter code.

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Aug 21, 2008

SOURCE: Sentry Model 1610 Won't Open

Hello,

I am a Safe Specialist i have been reading some of your problems and this should help there is no code if you have lost yours only the default code for the model 1610 the default code is: 77,22,09,11,64 try that if you havent changed it and with this problem with people not getting the handle open with the green light happening i suspect this is a issue with the lock mechanism i have had many of the same problems with people bringing them in when you get you safe open it and where the lock is put some lubricate on the lock regulary as the lock sticks and wont open if you havent done this then you cannot get it open see you local safe specialist and tell them what i have said and they may or may not be able to get your safe open i hope this has helped Rob Safe Specialist World.

Ad

Anonymous

  • 1 Answer
  • Posted on Mar 18, 2009

SOURCE: know combination, but cannot open sentry safe 1250

If you know the combination:

1) Turn the dial to the left a few complete rounds, then stop on 1st number.
2) Turning the dial to the right, pass up the 2nd number once, then stop on it on the next round.
3) Turn the dial to the left directly to the 3rd number then stop.

The handle should open now.

Anonymous

  • 1 Answer
  • Posted on Mar 23, 2009

SOURCE: Sentry Safe (DSW3607 Model) Won't Open

I finally ignored the poorly-written instructions for programming a personal code and simply entered the factory code first and then pressed the prog/enter code button.  The safe opened.  The instructions tell you to push the prog/enter code first and then enter the factory code or personal code to open the safe.  Wrong!  Do it my way should this problem happen to you.

A1 Locksmith Burlingame

  • 170 Answers
  • Posted on Aug 08, 2010

SOURCE: sentry safe, enter codes and nothing

These safe are easily opened by a good locksmith. So if you have items in the safe you need to get out a safe and vault tech could drill it open and repair it for a small fee. I really don't think it is the chip probably just a stuck solinoid.

A1 Locksmith Burlingame

  • 170 Answers
  • Posted on Aug 09, 2010

SOURCE: can not open my safe, sentry 3750

Sounds like all you might need is a new Sentry Safe battery pack to hold the batteries. As these sometimes short out from leaking batteries.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Changing the code on sentry safe csw3607

To change the code on a Sentry Safe CSW3607, follow these steps:
  1. Open the safe by entering the current code on the keypad.
  2. Press and hold the "*" button on the keypad for three seconds. This will put the safe in programming mode.
  3. Enter the current code on the keypad, followed by the new code you want to use.
  4. Press the "#" button to save the new code.
  5. Close the safe and test the new code to make sure it works.
It's important to note that the CSW3607 has a factory default code of "0000". If you have not changed the code from this default, you can simply enter the new code you want to use without going through the programming mode.
0helpful
1answer

I have a sentry safe csw3607 and I locked my book and keys inside. I can't find a factory code for my model anywhere online. Is there a factory code for this model?

if factory codes and how to open the safe were online their would be no reason for them then either notify sentery or a locksmith
0helpful
1answer

Safe will not open

Once you get the error light that means you are entering a user code that was deleted when the batteries went dead . Simply use the master code in your owners manual to open the safe. Reprogram new user code instructions bottom of this page.
12helpful
2answers

Csw3607 sentry safe will not open. when i use my 5 digit code the red light beeps 5 times. when i use the factory code it does the same thing. Sentry has told me to take it to a locksmith and have them cut...

I hate to tell you, I just had this same problem on a brand new safe (x-mas present) and ended up having to crack it open. Unfortunately, from my extensive research on this problem on Sentry Safes it turns out that they use an encoded IC chip on the solenoid and if either a serial wire breaks going to the board or the IC chip fails, you get the 5 beep-of-death error. Needless to say, I'm thoroughly disappointed in Sentry and will discourage anyone from purchasing their products!
0helpful
2answers

Sentry safe, enter codes and nothing

Motorola IC #MC68HRC705 will not reset. Chip is most likely bad. Time to throw this safe out...Thanks for your answers. George
1helpful
2answers

When i put my last digital number in the red light comes on and error blinks i have a safe with the key and then you put 5 digits in and turn the lever then it opens the sentry safe A5 406618

When the red light blinks that means you are entering the wrong code. If your batteries went dead the safe delets the user code Check your owners manual for the default factory code number. Programing instructions.
1helpful
1answer

My sentry safe will not open after entering the code it reads "err"

You have to press the program / enter button after you enter the code How to open electronic sentry safes.
Locksmith opening instructions manual for sentry fireproof electronic security safes. Insert the tubular sentry key into the lock to the left of the key pad. Turn the key all the way to the right until the plunger pops out. Press the five-digit factory code. The green Proceed light will come on. Pull the handle down; to crack the sentry door open
0helpful
1answer

Sentry Model 1610 Won't Open

Hi,
here is the customer service phone number for you. I am sure they will be able to help you. 800-828-1438
19helpful
12answers

Sentry Model 1610 Won't Open

Hello,

I am a Safe Specialist i have been reading some of your problems and this should help there is no code if you have lost yours only the default code for the model 1610 the default code is: 77,22,09,11,64 try that if you havent changed it and with this problem with people not getting the handle open with the green light happening i suspect this is a issue with the lock mechanism i have had many of the same problems with people bringing them in when you get you safe open it and where the lock is put some lubricate on the lock regulary as the lock sticks and wont open if you havent done this then you cannot get it open see you local safe specialist and tell them what i have said and they may or may not be able to get your safe open i hope this has helped Rob Safe Specialist World.
Not finding what you are looking for?

395 views

Ask a Question

Usually answered in minutes!

Top Sentry Home Security Experts

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

john h

Level 3 Expert

29494 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66957 Answers

Are you a Sentry Home Security Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...