Minolta X-370S 35mm SLR Camera Logo

Related Topics:

Posted on Nov 01, 2007

Konica Minolta X-370 Wont develop

My Konica Minolta x-370 takes pictures fine but when i develop the pictures, the person behind the counter said there was no pictures on the film

2 Answers

A

Anonymous

Two possibilities 1) film was not properly loaded ( and so what you took to the lab was a blank , unexposed film ) or 2) shutter is not opening . To check set camera to slow speed like 8 th of a second open back and see if you get proper opening/closing of shutter. If not then camera will have to go in. Cost ? not more than $100.

A

Anonymous

Two possibilities : 1 ) your film was not properly loaded into the pick up spool and hence it was transported or exposed ; what you took to the lab was unexposed film. 2) the shutter is not opening and again no exposure takes place. To check this open back , set to slow speed like 8th of a second, and see if the shutter opens and closes properly. If the shutter does not open then it will have to go in, unfortunately. Cost ? If it is just an adjustment ( as I suspect is the case ) you should not pay more than $ 100.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

No drum replace & developed replace how to sole konica minolta bizhub 206 error code m2 reset

did you clear the counters for the drum and developer FIRST if not get a new drum and new developer as both are replaced at the same time. As the machine uses the counters to determine a a new unit and adjust certain voltages to certain units accordingly. Other wise machine thinks it is old when it is new and causes image issues and codes

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

1helpful
1answer

How to replace developer in konica minolta bizhub 500

First service mode to clear the counter, then remove the developer section, dump old developer replace with new developer then run TCR adjustment. recommend replacing the drum and cleaning blade at same time.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

0helpful
1answer

Konica minolta bizhub 282 c2557 code appears after F8 ran and new related parts were replaced?

Did you replace the developer unit along with the new developer? mite have bad ATDC sensor bottom of developer unit

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

1helpful
1answer

Konica minolta 282 c2557 code appears after developer was replaced and counters were cleared and f8 was run

After clearing the counters did you touch "END" and then power off the machine. Check your counters again if they did not clear get new developer and drum and start over

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

0helpful
1answer

Konica minolta 185 m2

Clear the counters for drum and developer, Replace the drum and developer, run required process, done, Do not reset without replacing because copier uses the counter if you reset without replace code and image problems will begin. Because copier will think drum and developer are new when in fact there are not and voltages set for new will be working on old stuff.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

0helpful
1answer

Konica minolta bizhub 195 shows M2 error after changing the developer how to reset M2 error?

Did you also replace the drum, clear the developer counter first before installing the developer, and run the required F 8 procedure after the developer was installed, As the machine uses the counter to control voltages to certain assemblies, not replacing the parts and resetting the counter will cause codes and image issues.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

0helpful
1answer

How to enter f8 function in konica minolta ineo250

Utility/counter, details, stop 00 stop 01, function F8 was developer replaced before you do this WAS THE DEVELOPER COUNTER RESET before you put the new developer in. The machine runs on the counters if you did not reset the machine will think the developer is old when in fact it is new and will cause image issues and codes

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

0helpful
1answer

How to reset imaging unit for konica minolta bizhub211

IS the drum cleaning blade and developer been replaced. Counters are to be cleared before replacing the drum and developer, because the machine use the counter to determine voltages to certain assemblies. If you reset the counter and have not replaced the parts then the machine will think the parts are new when fact they are not and cause image problems and codes. Was the F8 run after new developer was replaced. DO not allow any printing or copying until that is done, or you will have to replace the developer again.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

0helpful
2answers

Wrench symbol on Konica 7115 means what?

PREVENTIVE MAINT. Replace drum, cleaning blade,developer etc. comes as a kit for the technicians to replace, clearing counter without doing things not good machine uses the counters to adjust voltage on certain parts and is the only way it knows new parts installed clear counter and not replace parts causes codes and image problems

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

0helpful
1answer

KONICA MINOLTA BIZHUB163 MAINTENANCE CALL M2

Replace the developer and drum make sure counters are cleared for the drum and developer. because machine works off the counters if the counters are clear it assume new drum and developer are installed and set voltage to the drum and developer based on it, if in fact he drum is not new or developer then image problems and code can appear


try web site below as start to get parts, recommend Konica Minolta tech do it.


Precision Roller Printer Toner Cartridges Parts and Supplies Office...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Not finding what you are looking for?

229 views

Ask a Question

Usually answered in minutes!

Top Minolta Photography Experts

Cindy Wells

Level 3 Expert

6688 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

k24674

Level 3 Expert

8093 Answers

Are you a Minolta Photography Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...