Initializing scanner please wait - HP LaserJet 4730 MFP Printer

I need to ask you this. Normally one bank can't be closed.
You may need a soft or hard reset. Here's some reading and instructions.
Please use this first!

resetting your scanner
1. Turn off your scanner, and then turn it on again.

2. Insert a pointed object into the reset hole on the back

of the scanner. Then, gently press and release the reset

button. Pressing reset does not clear the scanner's
working memory or the V-Scanner folders.

If this doesn't work here's step two! CAUTION. THIS WILL ERASE EVERYTHING, but it MAY Fix the Problem!!

Initializing your scanner clears all information stored in your
scanner's working memory. Initialize your scanner only when
you are sure it is not working properly. V-Scanner memory is
not affected when you initialize the scanner.

1. Turn off the scanner, and turn it on again. First, the DSP
boot version, and then Welcome To Digital Trunking appears.

2. Press 0. The following messages appear on the display:

System Tests

Select Test
Exits if no
Key Press

3. Press 1. The following messages appear on the display:

Factory Init
Erase Memory
ENTER if Yes
CL to EXIT

4. Press ENT. The following messages appear on the display:

Initializing
Clr Main Mem
V-Scan is OK
Please Wait

5. Do not turn off your scanner until the initialization is
complete. When the initialization is complete, M000 and
Bank 0 Ch 00 appear on the display.

If that doesn't help. Please get it serviced. I do recommend to get a DSP Firmware Update for it. The download is free from RadioShack but the cable and software is not.

I hope this helps and solves this problem.
btw.. if you don't have the product manual http://support.radioshack.com/manuals/ome20-496.pdf
You will need Adobe reader or equivalent!!
Happy Scanning!!

Please try this!!
You may need a soft or hard reset. Here's some reading and instructions.
Please use this first!
resetting your scanner
1. Turn off your scanner, and then turn it on again.

2. Insert a pointed object into the reset hole on the back
of the scanner. Then, gently press and release the reset
button. Pressing reset does not clear the scanner's
working memory or the V-Scanner folders.

If this doesn't work here's step two! CAUTION. THIS WILL ERASE EVERYTHING, but it MAY Fix the Problem!!

Initializing your scanner clears all information stored in your
scanner's working memory. Initialize your scanner only when
you are sure it is not working properly. V-Scanner memory is
not affected when you initialize the scanner.

1. Turn off the scanner, and turn it on again. First, the DSP
boot version, and then Welcome To Digital Trunking appears.

2. Press 0. The following messages appear on the display:

System Tests

Select Test
Exits if no
Key Press

3. Press 1. The following messages appear on the display:

Factory Init
Erase Memory
ENTER if Yes
CL to EXIT

4. Press ENT. The following messages appear on the display:

Initializing
Clr Main Mem
V-Scan is OK
Please Wait

5. Do not turn off your scanner until the initialization is
complete. When the initialization is complete, M000 and
Bank 0 Ch 00 appear on the display.

Hope this works.. Happy Scanning

I need to ask you this. Normally one bank can't be closed.
You may need a soft or hard reset. Here's some reading and instructions.
Please use this first!
resetting your scanner
1. Turn off your scanner, and then turn it on again.

2. Insert a pointed object into the reset hole on the back
of the scanner. Then, gently press and release the reset
button. Pressing reset does not clear the scanner's
working memory or the V-Scanner folders.

If this doesn't work here's step two! CAUTION. THIS WILL ERASE EVERYTHING, but it MAY Fix the Problem!!

Initializing your scanner clears all information stored in your
scanner's working memory. Initialize your scanner only when
you are sure it is not working properly. V-Scanner memory is
not affected when you initialize the scanner.

1. Turn off the scanner, and turn it on again. First, the DSP
boot version, and then Welcome To Digital Trunking appears.

2. Press 0. The following messages appear on the display:

System Tests

Select Test
Exits if no
Key Press

3. Press 1. The following messages appear on the display:

Factory Init
Erase Memory
ENTER if Yes
CL to EXIT

4. Press ENT. The following messages appear on the display:

Initializing
Clr Main Mem
V-Scan is OK
Please Wait

5. Do not turn off your scanner until the initialization is
complete. When the initialization is complete, M000 and
Bank 0 Ch 00 appear on the display.

If that doesn't help. Please get it serviced. I do recommend to get a DSP Firmware Update for it. The download is free from RadioShack but the cable and software is not.

I hope this helps and solves this problem.
btw.. if you don't have the product manual http://support.radioshack.com/manuals/ome20-496.pdf
You will need Adobe reader or equivalent!!
Happy Scanning!!

Scanner Error
The device has experienced an internal hardware error.

• Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the device to initialize.If the error persists, replace the scanning assembly.

Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the device to initialize.
If a surge protector is being used, remove it. Plug the device directly into the wall socket.
Use thepower switch to turn the device on.

Sounds like the motherboard is corrupted. Please try these steps again. Thanks!! Happy Scanning!!

I need to ask you this. Normally one bank can't be closed.
You may need a soft or hard reset. Here's some reading and instructions.
Please use this first!
resetting your scanner
1. Turn off your scanner, and then turn it on again.

2. Insert a pointed object into the reset hole on the back
of the scanner. Then, gently press and release the reset
button. Pressing reset does not clear the scanner's
working memory or the V-Scanner folders.

If this doesn't work here's step two! CAUTION. THIS WILL ERASE EVERYTHING, but it MAY Fix the Problem!!

Initializing your scanner clears all information stored in your
scanner's working memory. Initialize your scanner only when
you are sure it is not working properly. V-Scanner memory is
not affected when you initialize the scanner.

1. Turn off the scanner, and turn it on again. First, the DSP
boot version, and then Welcome To Digital Trunking appears.

2. Press 0. The following messages appear on the display:

System Tests

Select Test
Exits if no
Key Press

3. Press 1. The following messages appear on the display:

Factory Init
Erase Memory
ENTER if Yes
CL to EXIT

4. Press ENT. The following messages appear on the display:

Initializing
Clr Main Mem
V-Scan is OK
Please Wait

5. Do not turn off your scanner until the initialization is
complete. When the initialization is complete, M000 and
Bank 0 Ch 00 appear on the display.

Please try this!!
You may need a soft or hard reset. Here's some reading and instructions.
Please use this first!
resetting your scanner
1. Turn off your scanner, and then turn it on again.

2. Insert a pointed object into the reset hole on the back
of the scanner. Then, gently press and release the reset
button. Pressing reset does not clear the scanner's
working memory or the V-Scanner folders.

If this doesn't work here's step two! CAUTION. THIS WILL ERASE EVERYTHING, but it MAY Fix the Problem!!

Initializing your scanner clears all information stored in your
scanner's working memory. Initialize your scanner only when
you are sure it is not working properly. V-Scanner memory is
not affected when you initialize the scanner.

1. Turn off the scanner, and turn it on again. First, the DSP
boot version, and then Welcome To Digital Trunking appears.

2. Press 0. The following messages appear on the display:

System Tests

Select Test
Exits if no
Key Press

3. Press 1. The following messages appear on the display:

Factory Init
Erase Memory
ENTER if Yes
CL to EXIT

4. Press ENT. The following messages appear on the display:

Initializing
Clr Main Mem
V-Scan is OK
Please Wait

5. Do not turn off your scanner until the initialization is
complete. When the initialization is complete, M000 and
Bank 0 Ch 00 appear on the display.

Hope this works.. Happy Scanning

If all else fails, you can RESET or INITIALIZE the scannerto bring it back to normal operation.

To RESET:
- Power the scanner OFF
- Power the scanner back ON
- Insert a pointed object (paper clip, penpoint, etc.) into the RESET hole on the back of the scanner
- Gently press and then release the RESET button inside the hole.

NOTE: RESET will NOT erase the data that you've programmed into the scanner.

If RESET doesn't clear the problem, you can carry out the more drastic INITIALIZE process.

- Power the scanner OFF
- Power the scanner back ON
- Press 0 then 1 while "Welcome to Dual Trunking" is displayed.
- "Initializing Please Wait" will appear for about 2 seconds.

DO NOT power the scanner OFF until the INITIALIZE process is complete (M000 and Bank 0 Ch 00 appear on the display). The INITIALIZE procedure will reset the scanner to original factory settings and erase all data that you have programmed.

BillB

If all else fails, you can RESET or INITIALIZE the scanner to bring it back to normal operation.

To RESET:
- Power the scanner OFF
- Power the scanner back ON
- Insert a pointed object (paper clip, penpoint, etc.) into the RESET hole on the back of the scanner
- Gently press and then release the RESET button inside the hole.

NOTE: RESET will NOT erase the data that you've programmed into the scanner.

If RESET doesn't clear the problem, you can carry out the more drastic INITIALIZE process.

- Power the scanner OFF
- Power the scanner back ON
- Press 0 then 1 while "Welcome to Dual Trunking" is displayed.
- "Initializing Please Wait" will appear for about 2 seconds.

DO NOT power the scanner OFF until the INITIALIZE process is complete (M000 and Bank 0 Ch 00 appear on the display). The INITIALIZE procedure will reset the scanner to original factory settings and erase all data that you have programmed.

BillB

You may need a soft or hard reset. Here's some reading and instructions.
Please use this first!
resetting your scanner
1. Turn off your scanner, and then turn it on again.

2. Insert a pointed object into the reset hole on the back
of the scanner. Then, gently press and release the reset
button. Pressing reset does not clear the scanner's
working memory or the V-Scanner folders.

If this doesn't work here's step two! CAUTION. THIS WILL ERASE EVERYTHING, but it MAY Fix the Problem!!

Initializing your scanner clears all information stored in your
scanner's working memory. Initialize your scanner only when
you are sure it is not working properly. V-Scanner memory is
not affected when you initialize the scanner.

1. Turn off the scanner, and turn it on again. First, the DSP
boot version, and then Welcome To Digital Trunking appears.

2. Press 0. The following messages appear on the display:

System Tests

Select Test
Exits if no
Key Press

3. Press 1. The following messages appear on the display:

Factory Init
Erase Memory
ENTER if Yes
CL to EXIT

4. Press ENT. The following messages appear on the display:

Initializing
Clr Main Mem
V-Scan is OK
Please Wait

5. Do not turn off your scanner until the initialization is
complete. When the initialization is complete, M000 and
Bank 0 Ch 00 appear on the display.

Hope this works happy scanning!!