Reseting or clearing a radio shack pro 60 scsnner

• After you reset the scanner you have to initialize it again.
  

1. 1. Power the scanner off and on.
   
2. 2. Press and hold the "TUNE/CLEAR" key and stick the end of a paperclip in the reset hole and hit the rest button.
   
3. 3. Now remove the paperclip off the reset button and wait for the display to turn back on.
   
4. 4. Now release the "TUNE/CLEAR" key.
   

• The scanner is no initialized and ready to be programmed again.
  

• Now program the scanner.
  

1. 1. Press "PGM" key.
   
2. 2. Now enter a channel you want to store a frequency.
   
3. 3. Press "PGM" again.
   
4. 4. Now you will be on that channel.
   
5. 5. Now enter the frequency you want to program and don't forget the decimal.
   
6. 6. Now press the "ENT" key.
   

• Repeat steps to program more frequencies.
  

• Hope this helps.
  

To clear (RESET) the scanner:
- Power it OFF
- Press and hold the 2, 9, and HOLD keys and power the scanner ON

You can download and print the factory manual for your scanner, at no cost, here:
http://rsk.imageg.net/graphics/uc/rsk/Support/ProductManuals/2000516_PM_EN.pdf

Bill B.
Listening in since the 60's

The RESET function will clear everything that you have programmed into the scanner and restore original factory settings. You can, however, restore the 150 pre-programmed frequencies after a RESET.

To RESET:
- Power the scanner OFF.
- Hold down the 2, 9, and PSE keys and power the scanner ON.
- CLEAr appears on the display as the scanner resets.
- Do not power the scanner OFF until CLEAr disappears from the display.

To restore the original 150 pre-programmed frequencies:
- Turn the scanner power OFF.
- Hold down the 3 and ENT/PGM keys and power the scanner ON.

Bill B

My Uniden Bearcat BC 147 XLT will not broadcast. I have unplugged and reset it and installed new codes but, still nothing. What can I do?

Getting "stuck" indicates that the scanner may need to be reset to restore proper operation. This is a fairly drastic step that will erase ALL information that you've programmed into the scanner, but it's about the only fix. To reset the PRO-94:

- Turn the scanner OFF

- While holding down the 2 and 9 keys, power the scanner ON.

- CLEAR will flash for about 5 seconds as the scanners clears its memory and restores factory settings. Do not turn the scanner OFF or press any keys until the CLEAR message stops flashing.

Need the manual for your scanner? You can download/print it here:

http://support.radioshack.com/support_electronics/doc61/61426.pdf

Bill B

No telling what he did, but if you've tried deleting his entries and the scanner is still locked up, you'll need to reset it. This procedure will clear all the information you have have stored in the scanner.
1. Turn the scanner OFF.
2. While holding down the 2 and 9 keys, turn the scanner ON. CLEAR will flash for about 5 seconds while the scanner clears its memory.
NOTE: Do not turn the scanner OFF until CLEAR stops flashing.

Need the operating manual for your scanner? You can download;/print it here:

http://support.radioshack.com/support_electronics/doc61/61426.pdf

Bill B

Need to do a hard reset, turn power off, then back on. Hold down [CLEAR], press the reset button on the back then release [CLEAR]. I found it in the manual for the Pro-2018.

I would make sure you have
the new frequency # put in scanner
GOOGLE free new scanner frequency #
put in your town and city.

You can find a short list of police, and EMS freq. CLICK HERE

If you program all new codes it will automatically write over whatever codes you already have in there. If you just want to delete all the codes, then you have to go through and manually program them to 000.0000. If this doesn't work then ACE Hardware carries sledge hammers.