Sometimes the chair won't work at all

They sometimes come up on eBay or Amazon, but nothing at the moment. Take the existing remote to an electronics expert and ask if they can test the circuit board components.

https://www.google.com/search?q=HTT-10CRP+remote

Remote Repair

https://www.google.com/search?q=massage+chair+remote+control+repairs

..

good test method the motor works ok

faulty up down switch
or the part/solenoid ? that reverses the current to the lift motor so they run clockwise and reverse
for up and down the stairs

wow some have remotes
could be a faulty receiver it remote to the chair

OSIM uAstro2 Review Massage Chair Review try a different plug that has nothing else connected to it,,your manual,

http://www.brookstone.com/webassets/pdf/792590p_manual.pdf

I have been using power chairs for over 15 years. I have used or driven many brands/setups. If you're Invacare chair has six wheels that contact the ground all the time, this set up is horrible for anything other than a perfectly flat surface. My old power chair has six wheels, but the two front wheels only touched the ground on uneven surfaces or if the chair pitched forward. In Invacare's defense, their setup provides a smooth ride without pitching forward during fast deceleration. But, the "spring arm" tension on the front wheels is so strong that on uneven surfaces, they tend to lift the chair enough that you can lose traction, especially outdoors in the yard, etc. It is rather difficult to do, especially if you are unable to get down on the ground, but I have jammed small wooden spacers into the gap that opens up when the spring arm is lifted. It is difficult to see and difficult to insert the spacers, but the improvement is drastic. I used a small rectangular block of wood per side, almost 1/4 inch thick, and it raised the front wheels off the ground by about half to 3/4 inch. I used double-sided sticky foam strips to hold the blocks in place, but over time they eventually fall out. Maybe next time I will glue them in place. Hope this helps!

There are only three wires for this. either the wire is broke, or the switch.

hi paul.see if this link helps you out.
Massage chair panasonic The back rollers on my massage chair have stopped...

Common to go out Home Meridian......

Most RCA and GE TV sets use a four digit code to control the v-chip. The code reset procedure is different depending on the model. Try each method until you find one that works:

1. Hold down MENU on the remote and VOLUME DOWN on the TV it's self at the same time for at least 4 seconds. The set won't say so, but the lock will be unlocked

2. Hold down the 0 on the remote and the VOLUME DOWN buttons on the TV its self at the same time for at least 4 seconds. The set won't say so, but the lock will be unlocked

3. Hold down the MENU button on the front of the TV and the TV button on the remote at the same time for at least 4 seconds.

4. Hold down GO BACK on the remote and MENU on the front of the TV at the same time for at least 4 seconds.

5. Hold down EJECT on the front of the TV and the MENU button on the remote at the same time for at least 4 seconds.
Depending on the model, one of the methods should unlock the V-chip. Now, if desired, you can change the settings on the V-chip by going to the MENU and going to PARENTAL CONTROLS, or on some sets, going to MENU and then going to TV SETUP, then to V-CHIP SET.

the motors stick ( freeze ) i have heard that disconect the battery for an hour helps with this,and you may need to reprogram everything after..

Open the boot lid and drivers door, and switch on the ignition. Rock the valet switch, in the centre console, 5 times. The system will chirp to indicate it has entered learning mode.

On models with seat/mirror/steering wheel memory functions, the first remote will be linked to memory 1, second to memory 2 etc.

Press the larger, lock, button of the remote. The system will chirp to confirm it has got the signal. If it doesn't receive any signals for 15 seconds, it will chirp twice and exit learn mode.

To programme further remotes, rock the valet switch once. The system will chirp twice for remote number two, three times for number three etc, then press the lock button of the remote as above.

When finish, wait 15 seconds for the system to time out and chirp twice, turn off the ignition, close the doors and boot lid and the job is done!