Sound, no picture
SOURCE: Black picture, perfect sound
hi...your convergence IC's have gone bad.
These IC's operate at a very high temp, and usually only last 4-5 years.
If you remove the back of the set, you will want to look for the
BIGGEST heatsink in there, on that heatsink, you will see 2 large IC's ,
probably STK392-040, or STK392-120's or something close...regardless -
you can go on ebay to order the new ones, but MAKE SURE they are
Genuine SANYO IC's and not counterfiet cheapies. the cheap ones may
only last 2 months..
You will also need some "Heat transfer paste" - you can pick this up at radio shack.
Once you remove the old IC's, test all the large resistors near
them.. pull one side of the resistor out of the board so you can check
it out of circuit. they will usually have the value in Ohms, printed
directly on the resistor, but you may have to use the resistor color
code to find out what value they are....However, usually if there is
any damage, the resistor will look like it has been HOT or fried.
replace the IC's and any bad resistors, and you should be good to go.
If after replacing the IC's and any defective resistors, the
convergence is still bad, make sure to use a multimeter to check ALL
fuses on the boards, --- sometimes when the IC's go, they will take out
a fuse to the convergence power supply. If you find any bad fuses,
replace them accordingly!
Hope that helps u alot...
thank u!!!
SOURCE: sound no picture
If an LCD TV has sound but no picture do the following:
Use the source button to ensure that source is not set to the wrong input.
Try unplugging power cord for ten minutes, to ensure it is not a setting problem.
Check all the video cables at the back of TV.
Check Light /Color settings.
If problem persist and does not depend on external receiver or settings, then it is likely an internal fault.
If it has sound but no picture then one of the following parts is faulty, and must be tested and replaced:
Theinverter is the high voltage board that provides variable power to thebacklight lamp. This is the most common. When inverter is faulty youcan get no picture, or a very dim picture that can only be seen bypointing a torch light with a 45 degree angle on the LCD surface fromvery near distance.
The inverter must be tested by reading voltages with a multimeter.
The LCD ribbon cable/LCD display and connectors.
Thisis quite uncommon, but happens. If the TV had been hit or moved the LCDcable may have slipped out, or the LCD connector may be damaged.
The LCD controller board.
Thisis the board that controls the video signal, it is difficult to test,as there is need to read determined values on IC pins. To test thisboard you need to purchase a service manual and follow thetroubleshooting diagrams on service manual.
Input/Output Signal boards.
This are the boards where youconnect the video and audio cables, if a signal board is defective,then you may get no picture on particular inputs located on faultyboard.
If under warranty contact the manufacturer ringing the number on the user manual.
If you want to repair at your own expenses, just locate any good qualified repairer.
If you want to DIY you find parts here,
All: Appliance parts, electronics parts & more from PartStore.com
Encompass Parts Distribution
LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |
SOURCE: Thmy samsung LN-T3242H - 2 years old - the picture
Hi:
Make sure under your audio options you are in stereo mode and not it SAP, (Special Aided Programing).
SOURCE: LN-T1953H picture settings
It all depends on where the set is located. Try looking in the manual. Samsung has them online for free.
SOURCE: Samsung ln-t4042h turns on, plenty of sound, backlight works,...
Check the fuses on the T-CON board and also verify that it does have 12vdc feeding it. If you look at your screen in darkened room you will probably see slight glow on the front of the screen.
If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:
Please see my basic troubleshooting guide here:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
http://s807.photobucket.com/home/budm/allalbums
http://en.wikipedia.org/wiki/Capacitor_plague
Parts: www.shopjimmy.com
Of the LN-T series Samsung LCD TVs, those models whose last two digits are 61, 65, 66, 69, 71, or 81 (for example, LN-T4071F or LN-T466F) have the HDMI 1.3 interface.135 views
Usually answered in minutes!
×