Treadmill bolt is missing - Confidence Power Plus Motorized Electric Treadmill

please go to www.fitnessrepairparts.com and get the parts inmediately.
give the number, serial, and model numbers.
Happy New Year and God bless you

please go to www.fitnessrepairparts.com and get the parts

Happy new year. God bless you

put the belt on before you bolt the motor in

Installing An Icon Fitness Treadmill Belt- No Exposed Roller Bolts

You can save yourself a great deal of time by following these instructions as opposed to those of the manufacturer. Please contact us if you need any further help. UNPLUG THE TREADMILL BEFORE DOING ANY REPAIR!

Step #1- Before unfolding the treadmill, disconnect the lift shock from the ball joint. Most have a small retainer clip that can be pulled with a small flathead screwdriver and then the shock can be removed from the ball stud.

Step #2- Unfold the treadmill and then remove the three wiring connectors for the incline motor and then one of the incline motor mounting bolts.

Step #3- There are two shoulder bolts that hold the entire motor tray in place. These are at the back of the motor area and must be removed to gain access to the front roller bolts. Remove the two shoulder bolts and then you can pull the motor tray slightly forward or backward to gain access to the roller bolts.

Step #4- Follow the replacement instructions included with the walking belt.

Step #5- Reverse the process of step one, two, and three to reassemble the treadmill.

http://www.treadmilldoctor.com/installation?utm_source=fixya&utm_medium=cpc&utm_campaign=mendi

Step 1Confirm that the treadmill is plugged into a grounded, 120-volt electrical outlet. Examine the status of the power switch, located next to the treadmill's power cord. Set the switch to the "ON" position. Step 2Insert the red key into the slot set into the front of the console. Press and hold the button labeled "+" until the displayed speed reaches 5.0 mph. ad_order_1 = (typeof ad_order_1 === "undefined") ? "1" : ad_order_1; ad_client = "ca-livestrong_html"; num_ads = "1"; type = "text"; channels = "art_sub_top_Treadmill_Machines,article_top_fitness"; class_name = "adsense_afc"; print_google_ad(ad_order_1, num_ads, type, channels, ad_client , class_name ); Step 3Kneel down next to the rear panel of the treadmill's base. Locate the two bolts set into the rear panel. Examine the treadmill belt as it moves and determine which direction you wish to shift it. Step 4Select the appropriate bolt for your desired adjustments To shift the belt to the left, use the right bolt; to shift the belt to the right, use the left bolt. Step 5Insert one end of the Allen wrench into the top of your selected bolt. Turn the bolt a quarter turn clockwise. Examine the treadmill belt and determine if it is in the proper position. If necessary, make up to two additional quarter turn adjustments; if the belt is still out of alignment, move to the other bolt and give it a quarter turn counterclockwise up to a maximum of three times. Alternate between bolts as necessary. For make it easy to you have added video. Just watch it.

Here you can find parts for a lot of Proform equipment. I would try to find your specific model there and see if they have it.

Here are two solutions one is to get the belt centered on the treadmill and the other is to tighten the belt.

There should be two bolts in the rear of the treadmill, one on each side. These bolts adjust the rear roller of the treadmill. The walking belt will always go to the side that is looser. To get the belt back on track, (if you can start the treadmill so the belt is running) tighten the bolt on the side that the belt has slipped to. Tighten the bolt a little bit at a time. If you tighten the bolt too much, then the belt will go to the other side.

To tighten the belt, start by locating the two bolts that adjust the rear roller (one on each side of the unit in the back). Run the unit at about 3 mph. Tighten the bolts a 1/4 turn at a time. Make sure that what you do to one side, you MUST do to the other side or the belt will get off center. After you tighten it 1/4 turn, check the belt to see if it is still slipping. If it is then tighten the belt 1/4 turn again. Continue until the belt does not slip, but do not tighten the bolts more than 2 full turns.

Here are two solutions one is to get the belt centered on the treadmill and the other is to tighten the belt.

There should be two bolts in the rear of the treadmill, one on each side. These bolts adjust the rear roller of the treadmill. The walking belt will always go to the side that is looser. To get the belt back on track, (if you can start the treadmill so the belt is running) tighten the bolt on the side that the belt has slipped to. Tighten the bolt a little bit at a time. If you tighten the bolt too much, then the belt will go to the other side.

To tighten the belt, start by locating the two bolts that adjust the rear roller (one on each side of the unit in the back). Run the unit at about 3 mph. Tighten the bolts a 1/4 turn at a time. Make sure that what you do to one side, you MUST do to the other side or the belt will get off center. After you tighten it 1/4 turn, check the belt to see if it is still slipping. If it is then tighten the belt 1/4 turn again. Continue until the belt does not slip, but do not tighten the bolts more than 2 full turns.

Here are two solutions one is to get the belt centered on the treadmill and the other is to tighten the belt.

There should be two bolts in the rear of the treadmill, one on each side. These bolts adjust the rear roller of the treadmill. The walking belt will always go to the side that is looser. To get the belt back on track, (if you can start the treadmill so the belt is running) tighten the bolt on the side that the belt has slipped to. Tighten the bolt a little bit at a time. If you tighten the bolt too much, then the belt will go to the other side.

To tighten the belt, start by locating the two bolts that adjust the rear roller (one on each side of the unit in the back). Run the unit at about 3 mph. Tighten the bolts a 1/4 turn at a time. Make sure that what you do to one side, you MUST do to the other side or the belt will get off center. After you tighten it 1/4 turn, check the belt to see if it is still slipping. If it is then tighten the belt 1/4 turn again. Continue until the belt does not slip, but do not tighten the bolts more than 2 full turns.