Question about Dell /Poweredge 6650 BackPlane 2+3 Board (83PKM) Motherboard

1 Answer

Bootup Problem. The server is not booting up and it is showing a message to press F1 to reboot or Press F2 to enter the setup but it is not rebooting on pressing F1.It contains 1 ISCSI BIOS and 2 Emulex BIOS which however are disabled.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 449 Answers

Try getting BIOS access by pressing F2. Then try rebooting.

Posted on Jul 17, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My dell power edge is not booting everytime it is asking to press or F1 or F2 but still doesnot reboot


perhaps your hardware isnt correct setup in BIOS or some of harddrive not working correct

Jun 06, 2014 | Dell POWEREDGE 2900 Server

1 Answer

I have an Optiplex GX 620 Mini Tower that displays a NIC failure error at boot. The error message reads "NIC failure. Press F1 to reboot or F2 to go in to setup." The PC did not boots


it means your hard disk is not detected by system, check all connections of hard disk, if problem remains check with another working hard disk

Jul 29, 2012 | Dell OptiPlex GX260 PC Desktop

1 Answer

My pc dell optiex gx270 when i attach 1 hardrive in computer in start up time in black screen message 0 seek failure , boot press f1 to stup press f2 when i press f1 message not boot drive find when go to...


once in the setup (F2 at boot) turn on Caps Lock, NumLock and Scroll Lock (all 3 keyboard lights on)
Press ALT + E (system should beep once) Press ALT + F (System should beep once) Press ALT + B (System should reboot and re-detect drives)

Aug 05, 2011 | Dell Dimension 3100 PC Desktop

1 Answer

Dell poweredge 2600 server recently display a message " No boot device available Press F1 to reboot or F2 to setup" Please why?


Did you experience a power event? Go to BIOS (F2), and make sure that RAID is Enabled. If RAID got turned off (power event, BIOS reset), then it will give you that message. If RAID is already enabled, then you may need to repair your operating system. If something else happened (drive failures, drives removed, etc.), then the array may be completely gone. Call Data Recovery services if it is critical you retreive the data.

Aug 03, 2010 | Dell PowerEdge 2600 Server

1 Answer

Cant get 4600i started. powers up but will not get past intro screen. screen shows F1 to continue and when i press F1 it tells me to press it again to retry reboot, F2 for setup options.


you need to go to cmos or bios setup, set all the date and time and proper boot setting there save and exit, it is a cmos or bios failure that causes these problems try replacing the cmos battery if the message still continues

Nov 22, 2009 | Dell Dimension 4600 PC Desktop

1 Answer

Bootup Problem of Dell PE6650


Your NVRAM was corrupted (probably by a dead CMOS battery) or your hardware configuration has cnaged (deah boot disk, etc). Enter setup to see if the date/time has reverted to a previous date. If so, the CMOS battery needs to be replaced and the BIOS reconfigured for the server. Otherwise, check to ensure that your disk configuration is correct. If the battery is not dead and your disk configuration is incorrect, you may have a bad hard disk.

Jun 05, 2009 | Dell /Poweredge 6650 BackPlane 2+3 Board...

1 Answer

I've installed a new hard drive and put in more RAM on my Desktop. Now i get this message WHAT DO I DO. The amount of system memory has changed. Primary hard disk drive 1 not found Strike the F1 key to...


Strike F2 to go to the bios to run the setup utility

Don't touch anything , save and reboot

If primary hard disk still not found

reboot press F2 to re-enter the bios

Look for Auto Detect Hard Disks

if the computer shows a hard drive is detected

set the drive to LBA if possible

save and reboot



Az.

Sep 15, 2008 | Computers & Internet

1 Answer

Toshiba A45-S150 PC Notebook


Boot the system up and hold down the‘Esc’ key, then press F1 when you get the check system message. You are then in the BIOS Setup OR press F2 after bootup. Note the method will depend with ur model.

Mar 11, 2008 | Toshiba A45-S150 Notebook

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell Computers & Internet Experts

Ekse

Level 3 Expert

13434 Answers

Clive
Clive

Level 3 Expert

4345 Answers

Alun Cox

Level 3 Expert

2679 Answers

Are you a Dell Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...