Motorolar brush charger

my sim card is bolock please unblock my sim card ph:8291756838

sir
welcome to fixya
you can find your unlock number for your phone in this site web
http://www.mrunlock.com/ and i hope to find what you need
addition if you need more explain you can asked me in any time and any problem you welcome

you can do this
but after that you would have to re download you apps

I would clean the contacts on the battery to be charged and the charger. You can do this with a discharged battery and the charger unplugged usins a small mechanics wire brush,they can be had made like a tooth brush and work well for tight places. Gently brush and then blow out with air. Make sure that battery is firmly seated in charger and if light continues to flash you probably need a new battery. Thank you.

There are number of free JAVA applications (which your RAZR supports) providing world radio stations directly to your phone. For example this one http://www.fileguru.com/Online-World-Radio/download.

I'm sorry but it cannot :(

Hello, when a phone does not charge, it means that the phone charger or the port at which the charger is inserted in the phone is faulty.

Might be due to dust or dirt. You can Clean charging port on the phone with a brush and alcohol to remove dirt.

After cleaning it,if still not charging, you can test charger with another phone to be sure if the charger is working. And if the charger works with another phone,that means the charging port on the phone is faulty and will need to replaced.

Take care.

(1) Detaching and refitting the drum unit
Procedure
1. Remove the developer unit (See page P.1-5-
9).
2. Open the left side cover and then remove
the waste toner box.
3. Unlock the drum unit lock and then remove
the drum unit.
4. Check or replace the drum unit and refit all
the removed parts

(1) Detaching and refitting the transfer roller and separation charger brush unit
Procedure
1. Remove the developer unit (See page P.1-5-
9).
2. Remove the drum unit (See page P.1-5-10).
3. Slide the paper chute guide and unhook the
hooks.
4. Remove the paper chute guide.
5. Remove the shaft (transfer roller) from the
both bushes.
6. Release the four latches and then remove
the separation charger brush unit.
7. Check or replace the transfer roller and separation
charger brush unit and refit all the
removed parts.
CAUTION: Note the following, when refitting
the separation charger brush unit.
A. The separation charger brush unit is
inserted into the two projections of the frame
and does not run on to the projections.
B. The separation charger brush unit is
firmly in contact with the separation charger
plate of the frame.

(1) Detaching and refitting the paper feed assembly (paper feed roller and pickup roller)
Procedure
1. Remove the paper cassette.
2. While pushing the lock and then slide the
paper feed roller pin.
3. While pressing the lever and then remove
the paper feed roller assembly.
4. Check or replace the paper feed assembly
and refit all the removed parts.

(2) Detaching and refitting the ****** roller
Procedure
1. Remove the paper cassette.
2. Push the bottom plate down until it locks
(30/31 ppm printer [EUR/USA model] only).
3. Unlatch the two latches and then remove
the ****** guide.
4. Remove the ****** holder (roller) from the
****** guide.
5. Check or replace the ****** roller and refit all
the removed parts.

Try going to your phone's organizer then to alarms or can go to where your phone's alarm feature is located....and select recurrent alarm. There you can find the options of the time of the alarm and the day you the alarm to recure....i hope I've give you the right solution for your problem, good luck!

if you look at the charger port you will see a metal sleeve around the inside. Itneeds to be bent a little in so it will make the soket tighter. then the socket needs to be cleand out with a small brush. I use a old dry tooth brush

I’m happy to assist further over the phone at https://www.6ya.com/expert/james_1cb31da1bc8c6102