HOW TO DISCONNECT THE BATTERY ON MY HANDSET

Contact Looking For Help

Mark
Motorola Mobility Support

remove my passward in my cell

WARNING: Restoring the handset will permenently Delete All Data, including Contacts
Note: All locked pictures, videos, ringtones, music, sounds and downloaded content will be permenently deleted when restoring the handset to the default settings.
To restore the handset to the factory default settings follow the steps below:

1. While in standby mode, press OK for Menu
2. Select Settings & Tools (9)
3. Select Phone Settings (6)
4. Select Security (9)
5. Enter the lock code, default password is the last 4 digits of cell phone number, unless it has been changed, then press OK
6. Select Restore Phone (5)
7. Highlight Yes, using the navigation keys
8. Press OK to confirm resetting the handset
9. Press OK at the re-program the phone screen
10. Enter the lock code again, default password is the last 4 digits of cell phone number, unless it has been changed
11. Press OK to confirm restoring the handset to the factory default settings

Note: Press *228 and SEND after the power cycle to re-program the phone
Hope this was helpful?

You have to enter the default security code
Default will be 0000 or 1234 or 12345 or 00000(For default code check user manual of user handset).
If these won't works somebody changed security code.
To reset security code you need to flash your handset

To flash you need *USB cable compatible with your handset *A C omputer *PC suite of your handset *Internet connection(Min speed 1Mbps)

To flash *Install the PC suite *Connect to USB *Open the PC suit *Select UPDATE PHONE SOFTWARE**
**Please don't disconnect while updation process

Problem My handset displays either LOAD DELTA FILE or LOAD DEFAULT DELTA FILE. What should I do?
Solution(s) Tip 1 of 2
If the handset is not responding normally, you may need to reset your telephone system. Complete the following steps to reset the telephone system:
Step 1: Disconnect the power to the telephone base.

Step 2: Disconnect the handset battery.

Step 3: Wait a few minutes and then reconnect the power to the telephone base.

Step 4: Reconnect the handset battery

Step 5: Wait about one minute for the handset to re-establish a link with the telephone base and then test the phone again.

If the handset displays 'Searching', 'Base' or 'Range out' on the screen, this indicates that the handset has lost its link with the base. The following procedure should be followed to help resolve the problem:

• Confirm that the power lead has not been inadvertently disconnected from the base.
• Ensure that the handset batteries are correctly installed and are fully charged.
• Ensure that the handset and base are within range of each other.
• Switch the mains power off, wait five seconds and then turn it on again. This will reset your product.
• Carry out a reset procedure on both the handset and the base to return the settings back to the factory default. Your user guide will guide you through the correct procedure.
• If none of the above remedies solve your problem, please contact the helpdesk.

you either need a new battery or some one droped the phone

Try taking the batteries out of the handset and unplugging the master base set. Leave for 15 minutes and then have a try. This often reprogrammes some handsets to the default mode.

I don't have a second handset, but I'll quote from the instruction manual - Try this,

Regsiter up to 5 GAP cpmatible handsets to your OT150 base. New handsets must be fully charged.

You can use the same handset at home as well as the office by registering it to 2 bases.

1. At the base: press and hold "FIND HANDSET". You hear 2 beeps and the in use light flashes. Youa re now in registration mode.

2. At the handset: Press "OK". scroll down (with down arrow) to "REGISTRATION" and press "OK".

3. "REGISTER" is diplayed. Press "OK". Any free base numbers will flash. Enter the number of the base you want using the keypad.

4. Enter the PIN Number (default = 0000) and press "OK"

5. The handset searches for the base and when registration is complete goes into standby mode.

To test the handset is registered. Press "FIND HANDSET" on the base and the handset should begin to ring. Press "FIND HANDSET" again to stop the ringing.


As I say this is taken word for word (with a few spelling mistakes no doubt) from the instructions. I Hope that it solves your problem.

If you still have problems or you don't have the PIN number, the helpline number is 0845 226 7794, or e-mail [email protected]

A) Ok first try to disconnect everything and connect all the batteries and cable back. Charge your batteries to full. Then if it still Out of range, do this with all your handsets.
- Disconnect the battery
- Hold the * and # key on the Handset and put the battery back without releasing the buttons. (now your in test mode)
- press the 2 softkey below the screen ( it's a factory reset, erase everything)
- You will see RAM/EEprom erase on the screen
-After the bip press end

B) OK! Now disconnect the power adapter from your base unit .
-Hold the memory button on your base and plug the power adapter at the same time. Then the base will bip to let you know that you done it correctly.
-after the bip press No.1 ( that's mean the handset 1 is de-registrer.
- Now De-register all the other handset by doing the part B again. But only changer the No.1 for 2 then 3 then 4.

C) Disconnect and reconnect everything and use your manual to register your handsets with the base and your done! Everything should be ok !