The red light keeps blinking on my phones and when I press the talk button I get a busy signal but I can still call on it but the red light keeps flashing when I turn the phones of.

it is the vmwi in the global set up
press the menu button
press the down arrow to get to answering set up
keep pressing the down button until you get global set up
press the menu button
press the down button until you get the vmwi word press the menu button
press the down button to change from no to yes
press the menu button then press end
the light will stop flashing
If you get it right , right it down as the nbn sets that light off on a regular basis

This is a dual frequency transmitter. (315/390) You need to select one button to program the TYPE 1 frequency of 390 MHz. Here's how:

Backwards compatable programming instructions for GT3-R dual-band remote: This is a 3 button remote, which can be used to operate up to 3 garage doors using IntelliCode radio controls. This remote is defaulted to operate the new IntelliCode 2 Genie garage door openers, but you can also program individual buttons to operate other IntelliCode 1 (pre 2011) models of Genie garage door openers made from 1998 to present. To change a button to operate a pre 2011 IntelliCode opener, the default IntelliCode 2 setting must be changed to IntelliCode 1. An LED light on the remote displays which mode the remote button is in: Red = IntelliCode 1 / Green = IntelliCode 2 To set one of the 3 buttons to be IntelliCode 1 (red), follow the instructions below:

1. Select a button on the remote that has not been programmed.
2. Press and hold that button for 10 seconds. Both Red and Green LEDs come on and stay on.
3. Press the same button twice to toggle IntelliCode selection from IntelliCode 2 to IntelliCode 1.
4. Press the same button again to confirm toggle. the LED should be Red. The IntelliCode selection for this button is set to IntelliCode 1.

You are now ready to program the remote to your garage door. Follow accompanying instructions for "Programming to IntelliCode 1 Genie garage door opener," or see below instructions: Programming Instructions: Gently press the Receiver Learn Code button on the power head receiver of your Genie garage door opener (motor head on ceiling in garage). This small, black, unmarked button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the motor head. When pressed, a radio signal indicator light will start blinking red for 30 seconds. After pressing the Learn Code Button, press your transmitter button twice for your system to grab the frequency and code it in. (Keep the transmitter you're tuning at least 2 feet away from the power head while tuning.) Press the transmitter button once more to test the system and start your door moving.

If your unit is a wireless keyboard only, then there is a button on the bottom of the keyboard and another on the receiver that is plugged into the usb port of the computer. In order to calibrate the system when it looses its signal, you have to press and hold both buttons down at the same time for 30 to 45 seconds. That means press the button the receiver and the button on the bottom of the keyboard at the same time and hold them down for 30 to 45 seconds. This will revive the signal and bring it back to working condition.

If your unit is a wireless mouse and wireless keyboard then there are probably 3 buttons involved that need to be pressed and held for 30 to 45 seconds at the same time. One button on the mouse, one on the keyboard and the last on the receiver.

If you press and hold the buttons down as explained above, it will correct the problem.

THE TURN SIGNAL AND FLASHER ARE TIED IN TOGETHER.YOUR FLASHER SWITCH IS ON THE DASH.ITS A ROUND RED BUTTON WITH A WHITE TRIANGLE ON IT.WHEN YOU PRESS THE RED FLASHER BUTTON ON DASH.IT WILL MAKE YOUR FRONT AND BACK SIGNAL LIGHTS BLINK.WHEN YOU WANT TO TURN OFF FLASHER THEN YOU PRESS THE RED BUTTON.IT WILL TURN OFF FLASHERS.

Start with your headset turned off. Press the talk button on the headset. Hold it until you see the light on the headset begin to rapidly blink red, blue, red, blue, red, blue, etc. Let go, the light should continue to blink red and blue. Go into your phones blue tooth menu and search for the headset. The phone will only find the headset if the headset is in pairing mode (blinking red and blue). The pass key is 0000.

If the FWD/DND light is lit solid, the extension is in DND if it's programmed properly. You can test this by pressing the FWD button and reading the display. It will clear and press it again and it will set and tell you what it did. (if DND and FWD are both set it shows 3 states).

At the phone, press intercom and dial *710x where x=2 for all calls, 3 for busy, 4 for no answer or 5 for busy/no answer plus the extension of the voice mail plus #. Your FWD light should blink and you have now set FWD to voice mail.

Carl

Press down the "find handset" button until the paging beep stops (about 5 seconds) and this will reset the indicator lights on the handsets.

Good luck. If you follow all of the above instructions and the red light keeps blinking, that's just the way it is. And that's according to the Philips tech support team. Especially if it's in relation to voice mail icon. The phone appears to think you have a voice mail message even if you've checked it and deleted them all or have no voice mail service whatsoever. So you may be stuck with the blinking red light forever.

I found that if I hold the "find hs" button on the BASE unit (right above the red charging light) for a few seconds, it works!! Thank goodness there is a solution! Thanks for the help.

I had this very same issue which was remedied when I unplugged the headset recharging dock for approximately 5 seconds then plugged it back in. After about 10 seconds everything re-synced and was fine after that. -No more blinking.