Cricut mini flashing red light - Provo Craft Cricut Disney Font Cartridge

try manufacturer or an online search using make and model

I hope this is helpful. http://help.cricut.com/sites/default/files/pdfs/1asettinguptheapp.pdf

If your Cricut machine is not cutting all the way through your material, or is only scoring the material, choose a machine below for specific troubleshooting tips. Fortunately this issue can usually be resolved with basic troubleshooting.

• Cricut Explore
• Cricut Personal, Cricut Create, Cricut Cake, Cricut Cake Mini, Cricut Expression
• Cricut Expression 2, Cricut Imagine
• Cricut Mini

correct cut settings.

Remove the blade housing, then remove the blade and ensure that there are not any bits of paper stuck to the blade or lodged inside the blade housing. Ensure that you replace the blade housing correctly into the machine. Once clean, test your cuts again. If the blade and housing are already free from debris, or cleaning it did not help, proceed to 3.

Try an arm buoyancy test: gently press down on the black arms that surround the blade housing and then release them. Do they bounce right back up, or do they stick or rub in any way? If they stick or rub, please contact Customer Care through one of the options below for further assistance. If they bounce right back up when released, proceed to 4.

Increase the machine pressure settings and try your cuts again. If this does not change the cut result, proceed to 5.

Increase blade depth by turning the dial at the top of the blade housing. If this does not change the cut result, proceed to 6.

Perform a Hard Reset on the machine. If this does not help, proceed to 7.

Check your machine's firmware version. If the firmware is not up to date, perform a Firmware Update using Cricut Craft Room, a Gypsy device, or Cricut Design Studio.

Retry your cuts with a new blade housing.

If the machine is still not cutting through materials, or is only scoring the paper, please contact Customer Care through one of the options below for further assistance.

Forced Firmware Update on the machine through Cricut Sync.

Retry your cuts with a new blade housing. If the issue persists, proceed to 8.

Attempt a Format and Restore on the machine through Cricut Sync. Please note that this step should only be taken if all other steps have failed to resolve the issue.

If this does not resolve the issue, please contact Customer Care through one of the options below for assistance.

new blade. If this does not help, proceed to 5.

Adjust/increase the Multi-Cut setting in the Cricut Craft Room cut preview screen and retry your cuts. If this does not change the cut result, proceed to 6.

Retry a cut using a new blade housing.

If the machine is still only scoring or not cutting through the material, please contact Customer Care through one of the options below for assistance.

I am having this problem also. The image i wish to cut is well inside the 12 inchs. Hope someone has the answer

Just follow the steps given at this link, and your cutter should begin to cut again. I just tried it and my cutter is back cutting. Cricut Craft Room Troubleshooting Cricut Help Center

You can call customer support. They will have you install the Cricut Design studio just so you can access the firmware update. You must find a PC to do this - it will not work on your Mac that you use for everything. After your 10 year old PC takes 40 minutes to install and open Studio, you run it and restart your Cricut and all of your green lights stay on. You re-run it just to be sure, and all of your green lights stay on. You call back customer support and they have you cut out the drive belt to disable your Cricut and take a picture of it, then they will send you a refurbished replacement Cricut - white and gray, not white and pink like you own. This was my experience today and my only used twice Cricut is now ready for garbage pickup.

Any resolution to this issue? I like stone234 have narrowed it down to the cricut not getting power past the power board. I tested the two prongs that feed the red and black power for the main board and no voltage. Cricut Exp 2. Powered on as soon as I plugged it in. Plugged in usb to computer, I didnt have the software so i searched for it then started downloading it and noticed the screen on the unit was frozen. unplugged it and after plugging it back in it wouldn't power back on.

Souns to me like the cutting slide head is binding or the material transprt has a meesed up gear train. Or the case has been fractured

The flashing "boat" in the middle of the viewfinder just means the button battery is dead. Camera will still work. It's the little pull-out light grey plastic thing that's next to the heel of your right hand when you're using the camera normally. You need a CR2025 cell.

i have NV-D60EN model panasonic mini dv camer but when i use to record and play back, its red light falshing for about some second later switching itself off. it does not function any thing so that if you don't mid give me the solution please

yours respectful customer
God bless you !!