Cannot print anything at all.

Silahkan Daftar WargaQQ Situs Link Alternatif Warga QQ Online Terpercaya

Have you tried a new toner cartridge, The toner cartridge has moving parts, and of the cartridge gets stuck, the printer may indicate a paper jam.

Also paper often tears when clearing jams, and the little shreds of paper can stay in the rollers of the printer and keep it jammed. Make sure to inspect all the rollers to make sure they move freely, and do not have anything stuck in them.

Before you can clear a "PAPER JAM" or "PRINTER JAM" error, you must locate where in the unit the paper is jammed.
First, unplug the machine for safety and disconnect the telephone line. Next, follow these instructions based on where the paper jam is located.


Paper is jammed inside the paper tray:

1. Pull the paper tray out of the machine.

1. Pull out the jammed paper to remove it.

1. Reload the paper in the paper tray.
   
   
2. Reinstall the paper tray.
   
   
   

Paper is jammed inside the machine:

1. Remove the jam clear cover on the back of the unit. Pull the jammed paper out of the machine.

1. Re-insert the jam clear cover.
   
   
2. If you can not pull out the jammed paper, lift the scanner cover from the right-hand side of the machine until it locks securely into the open position.
   
   
3. Remove the jammed paper.
   
   
   

   
   
   

4. Check the print head's position. In the example photo the print head is positioned at the left hand side of the platen area.
   
   

   
   
   
   

5. Gently move the print head to the center.
   
   
   

   
   
   Note Be careful to not force the print head to move.
   If the print head is positioned at the far right hand side, you cannot move it. Please contact Brother Customer Service from "Contact Us".
   
   
   
   

6. Examine under the print head. If anything is found, remove it.
   
   

   
   
   Note Use a flashlight if necessary to check thoroughly.
   
   
   
   
   
   

7. Lift the scanner cover to release the lock. Gently push the scanner cover support down and close the scanner cover.
   
   
   
   
   

   
   
   
   

8. Reconnect the power cord and telephone line.

Note To prevent paper jams, do not put multiple kinds of paper in the paper tray at the same time.

If the message continues to appear on the LCD, the machine will require repair. Please contact Brother Customer Service from "Contact Us".



Thanks for using fixya......

Try it maybe
The 6A00 is a Canon generic code for paper path jam.

Solution 1:
Move the printhead carriage back and forth a few times.

Solution 2:
Check the purge unit: Moving the print head assembly will not clear a purge unit if its jammed with paper, paper clips, push pins, screws, cookie crisp, flower bud pods or the like.

Solution 3:
Press the ink pads down in the purge unit.

Hi

Thanks for using FixYa. Before you can clear the error message, you must locate where in the unit the paper is jammed.

Unplug the machine for safety. Now follow these instructions based on where the paper jam is located.

1. Pull the paper tray out of the machine.
2. Pull out the jammed paper.
3. Reset the machine by opening the Upper Jam Clear Cover and then closing it.

If you cannot remove the jammed paper from the front of the machine, or the error message still appears on the LCD after you have removed the jammed paper, please go to the next step.

4. Remove the Lower Jam Clear Cover from the back of the machine. Pull the jammed paper out of the machine.

5. Put the Lower Jam Clear Cover back on. Make sure the cover is set properly.

6. Open the Upper Jam Clear Cover. Make sure that there is no jammed paper left in the corners of the machine.
Note: If the paper is jammed under the print head, unplug the machine from the power source, then move the print head to take out the paper. 7. Close the Upper Jam Clear Cover.

8. Close the output paper tray cover and slide it forward, then push the paper tray firmly back into the machine. While holding the paper tray in place, pull out the paper support until it clicks and unfold the paper support flap.

Please do rate the solution and revert for further assistance.

Thanks
Rylee

hi i hope i can help you? remove the cover from the machine and load paper as normal. and watch if the mechanics is sticking or anything that you can see give a clean with wd40clean all rollers check that you are puting in the correct amount off paper.check for loose connections.check for dirt on the switches.

OK, if the printer says jam but no paper inside and prints after you open and close the cover the paper likely never made it out of the tray. Or the machine thinks the page never made it out of the machine.
As far as input check your rollers 1 in the tray and the pick up roller in the machine if you don't have alot of pages on the machine these likely OK.
Next (and this I have found often) check the paper back stop in the tray. This is the guide to set the length of paper. If it is set just a little long the roller cannot catch the edge of the paper. Sometimes the teeth the guide sets in are broken or worn.
The output would be the sensor in the fuser replace fuser.
Hope this helps

Try pushing the print head carriage with a bit of gentle force. It is getting stuck, and hence the error. You may have to open side and top covers to reach this. Note: this is not the cartridges, but another device that moves back and forth on the slider carriage.