Braun electric water heater lid came off along with spring parts, all intact. How do I re-assemble it? Manual? Schematic available?

I just put in Tiger electric water heater parts came up with there wed site you can order parts on there .

The bowl and lid are no longer available and our out of production, at least Australia/New Zealand. Braun Food Processor Bowl BR67001126 Buy Online Need Part

see this steps and fix it. God bless you

Lid Switch Assembly

If the washer stops mid cycle the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.


Enter your model number to see parts for your washing machine.
Help me find my model number

Door Lock Motor and Switch Assembly

If the washer stops mid cycle the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.


Enter your model number to see parts for your washing machine.
Help me find my model number

Water Inlet Valve

If the washer stops mid cycle the water inlet valve cold water side may have failed. Most washers have a cold water rinse and so if they can't fill with cold water they just sit indefinitely waiting for the cold water to enter. If there is cold water to the water inlet valve and the cold water works in other parts of the cycle - or to make warm water - the valve is not the problem.


Enter your model number to see parts for your washing machine.
Help me find my model number

Main Control Board

If the washer stops mid-cycle the main control board might be defective. This is not common. Check other causes first such as the lid or door switch and other components.


Enter your model number to see parts for your washing machine.
Help me find my model number

Timer

If the washer stops mid cycle the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.

i could not find a user manual but follow this link to a schematic of the machine and its parts numbers hope this helps you

http://www.1800parts.com/images/1800Parts/English/products/standard/4169-Schematic.pdf

Try this out:

Parts are not available for WH21 240V water heater timer.
Timer has 1 year limited warranty.
http://www.intermatic.com/customer%20service/frequently%20asked%20questions.aspx
WH21 is rated for 25Amps and works on water heaters up to 4500Watts.
Look at label on side of tank to see wattage.
WH21 is SPST and turns off one hot wire to water heater.

I ran a business for many years.
Cost of stocking, organizing, and shipping parts is near same cost as new timer.

Following page shows selection of replacement timers:
http://waterheatertimer.org/Boxtype.html

For example, I have tested WH40 and T104 and other timers that show on page.
Trippers and motors are available for Intermatic box timers WH40 and T104, so you can maintain these specific models for many years.
http://www.grainger.com/Grainger/timer-accessories/timers/electrical/ecatalog/N-8hi
WH40 and T104 timers are SPDT and turn off both hot wires to water heater.
Both timers will work on any wattage residential water heater

http://waterheatertimer.org/How-to-wire-T104-Intermatic-timer.html
http://waterheatertimer.org/How-to-wire-EH40-hot-water-heater-timer.html

I have found two sources for Braun replacement parts; here and here.

Neither of these list the cover of the water reservoit as an available part.

Suggest you send an inquiry to each of these sites to see if this is a part they could source for you.

are you talking about springs under the center cutter bar between the foils? If so, you will need a new foil and cutter set. It is available at shaveroutlet.com with link below

http://shaveroutlet.com/braun-8000-series-360-complete-foil-and-cutter-p-143.html

Or maybe you refer to a spring that goes to one of the clips that hold the foil assembly to the pivoting swivel frame. If so, you will need the part linked below

http://shaveroutlet.com/braun-8000-series-activator-motor-drive-unit-p-36.html

If you are handy and know how to solder (and have the tools required), you can probably do the replacement yourself.

At the bottom of the razor are two plastic caps on either side of the charging port, you'll need to pry them out with a sharp pick or thin knive tip. Once removed, you can get to the screws that hold the front and rear case halfs onto the main shaver chassis where the PCB with the rechargeable battery is soldered onto the board.

Unsolder the battery and solder in the new replacement battery and put the case back together, making sure all the parts are in the correct posistion, and you're ready to recharge the shaver and start shaving again. If you're going to replace the internal board, it's just a matter of simply replacing the entire board and orienting the motor assembly connection onto the new PCB.

To find your replacement parts or batteries, try Electric Shaver Service. They also do repairs, so you might want to get an estimate if you don't want to do the repair yourself, etc. They're reliable and fast in getting shavers repaired and back to you quickly. 1-888-476-1785

Here's a link to the page with your battery on it and the toll free number to call for estimates too.

www.electricshaver.com

Hope you find this Very Helpful and best regards!