Emachines W3052 Gets stuck on logo screen when starting up.

If the battery is good then you need to change the memory ram.. that usually happens when the ram goes bad...tekgods.com

I’m happy to assist further over the phone at https://www.6ya.com/expert/jaime_08785c7d726a554e

eMachines flat-screen monitors offer high quality at low cost.
eMachines flat-screen monitors are compatible with most brands of PCs.
Issues with eMachines flat-screen monitors can arise from faulty power sources, cable problems and incompatible settings.
These issues can be resolved by testing step-by-step each possible cause.

Plug the computer's power cable firmly into a working AC outlet.
Press the computer's power button.
Check the LEDs on the front of the computer case to confirm that the computer receives power.
Plug the eMachines monitor's power cable into a working AC outlet.
Press the monitor's power button.
Check the LEDs on the front bezel or power button of the eMachines monitor to confirm that the monitor receives power.
Orange or blinking LEDs indicate low power or no signal.
Green LEDs denote a working connection..

Perform a monitor self-test.
Switch off the monitor.
Unplug the video cable from the monitor.
Press the eMachines monitor's power button.
An eMachines logo, Windows logo or "no signal" message indicates that the monitor is working properly.

Plug the eMachines monitor's video cable into the video port on the computer.
Attach the monitor's included DVI-to-VGA adapter to the monitor's VGA cable if your computer has a DVI port (15 or 25 pin-slots with 1 side slot) in place of a VGA port (15 pin-slots, no side slot).

Press the eMachines monitor's input button to change the monitor's setting to match the computer port used.
Set your monitor to DVI if connected to your computer's DVI port.
Set your monitor to VGA if connected to your computer's VGA port.

Connect the eMachines monitor to a known working computer with a known working video cable if the problem persists. Contact Gateway, eMachines manufacturer, if the monitor issue is not resolved.

Hi,

Some of the emachines coming with Recovery image. You need to press F11 key on starting to check whether the image is available or not. If it is there proceed with restore.

Otherwise you need a recovery CD to do this. If you don't have any CD then you could purchase the recovery disk for your emachines from the link below by entering the serial number on your computer:
https://secure.tx.acer.com/RCDB/Main.aspx?brand=emachines

Usually e-machine and other pc's have a factory restore setting set up in case of an error. You can; according to emachine tap the "Alt" and "F10" keys at the same time when the eMachines logo appears. Press "Enter" and follow the directions on the screen to recover the operating system back to factory condition. I hope that helps, if those keys don't work try F11 at the emachine logo. Good luck.

Follow this link and download the "Other Drivers for Motherboard Package"

The Ethernet Driver should be on there.


http://support.gateway.com/us/en/emac/product/default.aspx?tab=1&modelId=1440

Not sure that this is what you need, but should work. If you have Windows OS, try pressing F8 when booting. A menu will be given on the screen. Will have to choose SAFE MODE and when windows loads go to START MENU-PROGRAMS-ACCESSORIES-SYSTEM TOOLS and choose SYSTEM RESTORE

the following links will help you, same as 3052

http://downloads.emachines.com/drivers/bios/D00221-001-002_readme_em_us.txt

http://emachine.com/support/drivers.html

http://global-download.acer.com/GDFiles/Driver/Others/Others_eMachines_4.46_XPx86_A.zip?acerid=633937006283283102&Step1=Desktop&Step2=W%20Series&Step3=W3052&OS=X01&LC=en&BC=eMachines&SC=PA_6E

1. The emachines W3503 has an integrated ATI Radeon™ X300 based graphics card. It has also a PCI Express (PCIe x16) slot available.

2. The emachines W3052 has a NVIDIA® GeForce®4™ MX graphics card. I'm not sure whether it is integrated or not, but I'm sure that if it is not, it will be an AGP graphics card. Since The emachines W3503 has a PCI Express (PCIe x16) slot available for installing a graphics card, the swapping of graphics cards between the 2 machines is not possible since they support different types of graphics cards.

try this reinstall ur windows from ur emachine recovery cd and this should help let me know if it does

it is the mother board you will have to goto emachines website and order new one i had same problem in a few days it will get worse