R2 SWENT INTO STANDBY MODE AND WON'T COME OUT

On the front of the droid there is a red button that lights up when turned on & turns off after a couple of seconds, depress that button to free up the droid. Its called the wheel lock control button. That should free up your R2

Indicator Lights:
1.Headset Status Headset Indicator Light
2.Powering on Steady blue, then intermittent flashes
(changes to standby mode)
3.Powering off Red appears and goes off
4.Standby Blue intermittent flashes
5.Charging battery Red solid light. Light indicator turns off when
battery is fully charged and headset is off.
6.Low battery Triple red flashes
7.Pairing mode Blue/red alternating flashes
8.Missed call Purple flashes. Press the call control button
to cancel flashing light.
9.Incoming call Triple blue flashes when ringing.
Power on and off:
1.Turn on the headset Press and hold the call control button until the
indicator glows blue. You will hear ascending
tones.
2.Turn off the headset Press and hold the call control button until the
indicator glows red. You will hear descending
tones. When power is off, indicator stays off.
If none of this is helpful then it may be that your battery is dead, if that is the case then you will need to replace the whole headset. The battery's are not replaceable.

Good luck from Headsets Direct!

hi,
u can make your dvd for region free DVD play back. but for that you have to purchase an universal remote (ONE FOR ALL URC-7950). through this remote only you can make player DVD region free.
first of all u have to set( program) the remote for the same purpose.

Full procedure for the OneForAll URC-7950 remote is as follows:(preparing remote)

1. Press DVD
2. Hold the magic button until the Power key flashes twice.
3. Press 0533

4. Hold the magic button until the red led flashes twice.
5. Press 994
6. Press Magic key (don't hold)
7. Press 00189
8. Press 1 ( this sets it to key 1 - it flashes twice, if not repeat steps 4 to 8 )

9. Hold the magic button until the red led flashes twice.
10. Press 994
11. Press Magic Key (don't hold)
12. Press 00255
13. Press 2 ( this sets it to key 2 - it flashes twice )

14. Hold the magic button until the red led flashes twice.
15. Press 994
16. Press Magic Key (don't hold)
17. Press 00095
18. Press 3 ( this sets it to key 3 - it flashes twice )

19. Hold the magic button until the red led flashes twice.
20. Press 994
21. Press Magic Key (don't hold)
22. Press 00221
23. Press 4 ( this sets it to key 4 - it flashes twice )

24. Hold the magic button until the red led flashes twice.
25. Press 994
26. Press Magic Key (don't hold)
27. Press 00079
28. Press 5 ( this sets it to key 5 - it flashes twice )

The remote is now programmed and ready to use, to make the BDP-S370 region free

1. Use the remote that came with the player to bring the player out of standby, make sure there isn't a disc in it.
2. Press 1, 2, 3, 4, 5 on the OneForAll URC-7950 remote. The power light will start flashing. (blue middle light)
3. Put the player back into standby with the Sony remote.
4. Next time you turn on the player it will be region free for DVD playback.
OK

SETTING THE TIME AND DATE ON AN OLD 4 BUTTON DIGITAL WATCH

[L1] [R1]

[L2] [R2]

SETTING THE TIME.

Press [L2] to move through the modes. When the time display flashes, you are in the correct mode to set the time. The hours first, then the minutes and seconds.

Press [R1] to advance the numbers, [R2] to go to the next.

Press [L2] to save your settings. [L1] is not used; it's the light.

SETTING THE DATE AND DAY. After setting the time (seconds flashing) push [R2] to move though time, backwards, to date, [R1] to set day, [R2] to move to month [R1] to set the month. Push [R2] to get to the day of the week, then [R1] to change. [L2] to end.

If the lamp has been replaced I would think the Lamp ballast would be most likliest followed by the color wheel and then the Digital board. You can get any part needed for your model at www.tvrepairworld.com just leave them a email they respond quickly.

if it's under 1 year old, it's still under warranty, so send it in and get it fixed for free.

Try this out since it solved the same problem for me:

a) Turn your PS/2 on with the receiver plugged in. You'll get the green flashing LED on the receiver
b) Remove one of the batteries from the controller.
c) Keep R1 and R2 buttons together while inserting the battery back on the controller.
d) After 5 seconds or so release R1 and R2 buttons.

And that's it - at least for me.

I got this idea after checking Logitech site and reading about the analog controls calibration procedure (basically the same sequence while pressing L1 and L2 buttons).

Merry Christmas...

You either have a bad fan or one of the rotation sensors mounted on one of the fans has failed. Take the back off the set and see it the main fan slightly right of center is rotating. If it is, there are two more fans, one mounted right above the lamp and another on the optical block itself. You will have to pull the optical block to check those.

1. Make sure the player is switched on, and is at the Samsung logo screen.

2. Also check the tray is shut and that there's no disc in the player.

3. Now press the REPEAT button on the remote, followed by a five digit code.

4. This code is different depending on what region your player is *currently* set to: R1 - 29334 R2 - 38767 R3 - 56732 R4 - 76884 R5 - 53814 R6 - 24462 So for example if you have an R2 player, press REPEAT-3-8-7-6-7.

5. If you've done this correctly (and your player is compatible with the hack), you should see a number at the top left corner of the screen corresponding to the current region.

6. Now, pressing any number from 1 to 6 will change to the corresponding region. Or, press 9 for "auto-region" mode.

7. Next, press OPEN/CLOSE to open the tray, followed by Standby (or DVD POWER) on the remote to close it and put the player into Standby mode.

8. The next time you turn your player on, the new region will be set. Don't forget that if you want to hack it again, you'll need to use a different code, as listed above. If it's currently set to "region 9", use the code for the last *proper* region you set it to.

or this...

Multi-Region on a Samsung BD-P1000 R2:
1. Switch on unit
2. Remove any disc
3. Wait fo NO DISC message
4. Press REPEAT on the remote control (NOT REPEAT A-B)
5. Type 57538 followed by the desired region number on the remote control
NOTE: 9 = Multi Region mode
6. Press OPEN/CLOSE on the remote control
Switch unit off
7. Enjoy :0)

It seems obvious that you have a bad battery. You'll need to find a replacement.

Geno