Question about Microtek C593 15" Flat Panel LCD Monitor

1 Answer

Emachine destop not recognising acer lcd monitor

This secondhand desktop couldnt recognise flat monitor i attached to it. so i couldnt see if booting is ok. even if i have to find and download the monitor drivers online i couldnt because nothing shows on the screen except the 'no signal' message that came on briefly . how do i get the drivers, assuming this is what is lacking? the desktop is emachine. and the flat monitor is acer AL511

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,992 Answers

It sounds more like the computer isn't starting up. The "no signal" message is coming from the monitor itself to tell you it's on but there's nothing coming in to display. Normally no special drivers are required for the monitor, and you'd see at least the computer maker's splash screen and BIOS messages if the computer was starting up properly.

You'll need to determine what is keeping the computer from starting up. Make sure it's getting AC power and that the power light comes on when you press the front panel power button. You may need a power supply. If the computer comes on but doesn't boot you may have memory problems or trouble with the motherboard. But your monitor is working properly.

Posted on May 10, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Only one vga works


IF NVIDIA VIDEOCARD .IT HAS TO BE ADJUSTED IN SETTINGS

Apr 17, 2013 | Dell Dimension 5150 (DIM515MIN) PC Desktop

1 Answer

How do I get my laptop out of safe mode?


Let it start in safe mode, Once it boots up click Start/Programs/ and look for the RUN prompt. It might be under the Accessories folder. Once you get RUN to open type msconfig and press OK.

When the System Configuration window opens Click on the "Boot.ini" tab at the top and make sure the /SAFEBOOT option is not selected. If it is, remove the check mark then hit OK. Reboot and see if it goes to normal.

Apr 27, 2012 | Toshiba Satellite L505-S5966 Notebook

2 Answers

I am using LCD monitor LG, my son changed some settings which i don't know, Presently, the monitor says Out of range 53.6KHZ / 60HZ. What is the problem and How to solve this problem and restoration of my...


He may have changed the display settings on the computer. He may have altered the refresh rate higher than the monitor can handle.
You can try start the computer in safe mode (F8 repeatedly on boot up, till the safe mode option comes up)
This will load basic video drivers, you should be able to check your settings now.
Windows xp / right click on desktop and your settings are there
OR control panel / display

Sep 04, 2010 | Samsung 510N 15" Flat Panel LCD Monitor

1 Answer

I want to bypass the video card on the motherboard with a new one. How do I disable the old one?


When you say the video card on the motherboard I guess you are referring to the video graphics port at the rear of the motherboard? In some cases you don't need to disable the video port that is attatched to your motherboard. You can just purchase a new video card and when you insert it, plug your monitor cable into this port and when you start your computer it should be recognised. Just make sure that you match the video card connector to the type of video card slot you have on the motherboard. You will either have an AGP (Accelerated Graphics Port) slot or a PCI (Peripheral Component Interconnect) Express x16 slot but not both. Before purchasing the video card make sure you look very carefully at the minimum system requirements, it generally should be ok though. If you just want to improve the graphics then a standard card should be adequate. What type of monitor do you have, flat screen or old box (cathode ray tube)? If you have a flat screen then chances are it can accept a high spec card. Monitor and card have to be compatible.

If you need to disable your onboard video port though then you would do this by accessing what's known as Cmos Setup. When you boot up your computer it will tell you which key to press to access setup, it's normally F2 or the delete key. Once you press this you gain access to the settings and you can search for the ability to disable the onboard video port. I'm pretty sure that you don't need to do this though, when you insert your card it should be recognised. I hope this is somewhat helpful to you. All the best. Andrew

Jan 20, 2010 | Compaq D51C PC Desktop

1 Answer

USB drive full


What happens when you connect the drive to the computer?

May 23, 2008 | Computers & Internet

1 Answer

Wireless


try this http://www.bolthole.com/solaris/x86-laptops.html there will be alot of reading but i think it will help thanks ian C emmit6378@yahoo.com

May 11, 2008 | Toshiba Satellite 15" Flat Panel LCD...

1 Answer

Will not boot but runs and will not talk to monitor


hi mikebal26 this is nichu,ok let me make you clear that your system is not booting because your cpu is not recognising some of the hardware it may be either your hdd,ram or any other.
.
if your system does not boot it has nothing to do with your monitor and fans.fans keep rotating whenever you switch on your pc.check inside the cpu especially with your ram .

so first when you turn on the system press delete to check it in the bios settings , in that check bootable addins and in the bootable devices set
1st priority to-cd rom,
2nd priority to hard disc drive,
3rd to priority to floppy drive.

.save the above settings and then boot this will turn on your system .
this will solve your problem
.


bye,
take care & have a nice day.

Nov 12, 2007 | Compaq Presario 5000 PC Desktop

Not finding what you are looking for?
Microtek C593 15" Flat Panel LCD Monitor Logo

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Microtek Computers & Internet Experts

Thomas F. Schneider

Level 3 Expert

2715 Answers

William Miller
William Miller

Level 3 Expert

9179 Answers

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

Are you a Microtek Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...