No arrows on watch band to indicate how to remove links from ceramic watch

The arrows show which way the connecting pin comes out. You need a pin press. Take it to a local jeweller.

https://www.amazon.ca/Watch-Band-Tool-Kit-Grey/dp/B087N7FGZJ/ref=asc_df_B087N7FGZJ/?

Flip the watch band over and check the underside. Links that can be removed will have an arrow etched on them. The arrow's direction indicates which way to push the pin to slide it out of the link.

Watch Bracelet Link Removal Tool - Stauer

..

Searches related to how to remove links from a watch hope this helps you..

how to remove links from a watch michael kors
how to remove links from a watch without pins
how to remove links from a watch without tool
how to remove links from a watch band with arrows
how to remove links from a watch band
how to remove links from a watch bracelet
how to remove links from a watch band without tool
how to remove links from a watch without arrows

here is a video that will show you how to remove links on your ceramic watch band

You have to have a tool small enough to push out the links, usually there are arrows showing which way to push the pin the arrows will be on the band. take a small hammer and gently tap on the tool to push the pin out. The ceramic is very strong so the hammer is safe, i have shortened many of these.

Hi, sizing the bracelet on your ceramic watch may void its warranty, making it ineligible to receive service from the manufacturer. If you want to keep your watch covered under warranty, contact your watch manufacturer for information on their customer repair service.
If you want to remove it yourself, you need a watch pin removal tool. You can use a watch pin removal tool to remove the link pins that secure the clasp pieces to your ceramic watch band.

But if you don't have a watch pin removal, follow the instruction below........

• Find a clean, flat, well-lit work surface where you can size the bracelet of your ceramic watch. For best results, spread a soft optical cloth over your work surface and perform your repair on top of the cloth. The cloth will help prevent you from losing any small watch components, like link pins, that may be freed during repair.
• Wrap the ceramic watch band around your wrist and count how many links overlap. Use this as a guideline for how many links should be removed. Note that the actual number of links to be removed may differ slightly from the original estimate. Remove excess links from your watch band one at a time to make sure that you don't end up accidentally making the band too short.
• Remove the excess watch links from the ends of the band with the attached clasp pieces. Look between the removable ceramic watch links to locate the silicone connector pieces that join the links. Use a pair of small, pointed scissors to make a cut between the link and the silicone connector, this will free the excess links. Cut on the side of the link that faces the watch clasp. Repeat the process on the other side of the ceramic watch band.
• Remove the clasp pieces from the ends of the removed watch links. Examine the clasp pieces to look for the metal pins that hold them in place. Push out the metal pins with a push pin to free the clasp pieces. You can now reattach them to the ends of your ceramic watch band.
• Examine the newly-shortened ends of your ceramic watch band. Without the clasp in place the silicone connector pieces will be exposed. Note the two small puncture holes that go straight through the silicone connector. Insert the teeth of one of the clasp pieces through the holes in the silicone connector from the bottom. Fold over the other side of the clasp piece, reinsert the metal link pin and push the clasp to click it into place. Attach the second clasp piece to the other side of the watch band using the same procedure.

There is usually a pin to take out either in the front closest to the time or down alittle ways . To pop it out use a tint needle or a paper clip.

Thank you for contacting FixYa.

Place the watch face down on the cloth. This will help keep your watch from being scratched.

2

Examine the links closest to the buckle. These links will have small pin holes on each side of the link, as well as a small arrow engraved on the inner side of the band. These indicate the direction the pins must be removed.

3

Place the driving tool (a thumbtack will work) inside the pin hole in the band and push the pin out in the direction of the arrow. Remove the pin carefully from the other side.

4

Repeat Step 3 to remove any links needed to adjust the band properly.

5

Reattach the band to the buckle. Attach each end of the buckle back to the bracelet, driving the pin in the opposite direction from how it was removed (opposite the arrow).

Best regards. Jewel

Select a clean, flat work surface where you can perform your watch band adjustment. Put down a piece of felt to protect the face of your Casio. Turn on a lamp near your workspace to better illuminate the watch components with which you will be working.

Lay your Casio face down on the protective felt. Look for the small arrows on the back of some of the watch links; these arrows indicate the removable watch links and the direction their pins should be removed.

Locate the pin hole above the arrow on the removable watch links. Insert the tip of a watch pin removal tool, or push pin, into the pin hole. Apply pressure to the link pin, in the direction indicated by the arrow, to free the pin and remove the link. A pair of needle-nose watch or jewelry pliers can be used to help pull out stubborn link pins. Remove as many links as necessary for your watch to fit perfectly.

Reserve the links and link pins that you remove from your Casio Edifice watch. Store the removed watch components in a small, clear, plastic zipper bag. These components can be used when repairing or expanding your Casio watch band.

WARNING:Casio recommends that customers have their watch bands sized by an authorized Casio watch dealer. Sizing the band of your Casio Edifice yourself may void the manufacturer's warranty on your watch. Contact Casio customer support for more warranty information.

Wrap the watch band around your wrist to determine how many links need to be removed for the watch to fit properly.

2 Place the watch face-down on a flat surface.

3 Look on the back of the watch band. You will find an arrow that indicates which direction you should push the pins to remove the links.

Find the point at which the extra links need to be removed for your watch to fit your wrist. Using a 1 mm flathead screwdriver (or the edge of one side of a pair of tweezers), push the pins in the direction indicated by the arrows.

Finish removing the pins with your pliers.

Keep the extra links in case you ever need extra room on your watch band.

For further assistance, check out the link:
http://www.pulsarwatches.com/home2.asp#FAQ

Ceramic links break VERY VERY Easily!!! Take your watch to a reputable watch repair shop and have them adjust your watch band! :-)