Bosch wtv74309GB error code F09 - Bosch Exxcel WVT 2850 Front Load Washer / Dryer

I welded the cable after cutting the wire inside the encoder but after running the machine , it displayed an error F09 in spindle control unit module.
having the F09 Fault, is it necessary to do a reset for Simodrive 611 to see if the fault no longer exists or not.
and if yes, how to reset the fault code f09 that is displayed

F-09 = Motor encoder system is faulty. Check motor encoder cable or motor encode

LOTS of fault codes here, but NO "E90"

BOSCH Side by Side Refrigerator Error Fault Codes Error Codes

Then there is this:

"Most of the times when the F:09 Error code apears on a Bosh Dryer is due to the thermal cut off being triggered, you can correct this issue by simply disconnecting the power to the unit and removing the back panel of the machine where you will find the button to be red. simply press it in and test the unit... if this doesn't resolve the issue, most likely your belt snapped off and would need to be replaced."

My Bosch dryer has error code 09 What does that mean

And if THAT is not enough, WATCH THIS!

Bosch Condensing Dryer F09 Error

Anthony

Hi Jeff, As you can see there's 3 different Bosh washing machine models, Hope you can find your error code.... CHEERS..

Bosch Washing Machine Fault Codes

F16 - Door lock error
F17 - Inlet valve error detected
F18 - Drain error detected
F23 - Anti flood device has been activated
F34 - Door lock error
F42 - Motor fault
F43 - Motor fault
F44 - Motor fault

Bosch WAE Range Washing Machine Fault Codes

F16 - Door lock problem
F17 - Inlet valve
F18 - Drain pump
F21 - Motor
F23 - Anti flood system activated

Bosch WFP Range Washing Machine Fault Codes

F01 - Water intake timeout
F02 - Heating timeout
F03 - Draining timeout
F04 - Motor fault
F05 - Uncontrolled motor startup
F06 - Short on NTC Detected on hot water intake
F07 - Open circuit NTC Open circuit wiring
F08 - Door open when program started
F09 - Unexpected heating
F10 - Communication error
F11 - Overheating
F12 - Short circuit
F13 - Mains voltage too high
F14 - Mains voltage too low
F15 - Faulty temperature sensor on motor PCB
F16 - Faulty rinse sensor Displayed only in test

How To Fix Maytag Washer Error Code F9 E1 ...

www.appliancerepairlesson.com/2013/.../maytag-washer-error-code-f9-e...

Dec 10, 2013 - The error code F9 E1 will be displayed on most newer Maytag washers and ..... My whirlpool duet wfw94heaw0 gives the error code F09 E01.

KitchenAid f09 error code Dishwashers Questions ... - Fixya

Really need the make and model as different manufacturers use the same code to mean different things. Hotpoint/Indesit/Creda F09 on almost all appliances means "Eprom Fault" this is a problem with the main control chip and you will need an engineer to reprogram the main module or swap it out. If it's Bosch, then the good news is F09 means "Heater Fault" which almost certainly means a cheap £20 replacement heating element needs fitting

F09 error is no heating, you can fix that by opening up the back and pressing the red cutout button which will restore hot air.

A typical HE3 Kenmore Elite washer the F09 code indicates and overflow has been sensed. This can be because of suds or a failure of the pump or pressure switch.

Suds is a common problem with the newer 2X-3X super concentrated detergents.

A pump that is partially blocked might cause this error

How long is the connection including the duct work in the house?

F09 error is no heating.
You can fix that by opening up the back and pressing the red cutout button which will restored hot air.

Good Luck,
I hope this helps

Your vcr seems to use the K Mech. F04 Means that the mechanism locks unloading.
The cause of which might be the loading motor timing.
F09 means No serial clock linking IC2004, IC7005 and IC7701.