Need to know how to configure dlink dsl 2640 modem for bsnl broadband

There a great article at General Router Setup.
If you need more help post back!
Thumbs and testimonial are welcome!

Go to D-Link - TechSupport FAQ

I HAVE A DNA-A211-I BSNL MODEM. I RESET IT CONTINUE 4-5 TIME AND AFTER RESET IN MODEM DSL AND WLAN IS NOT WORKING AND MODEM IS NOT CONNECTED TO MY PC. I USE WINDOWS 7 HOME PREMIUM. RESET BUTTON IS NOT WORKING. SO PLS SOLVE MY PROBLEM.

Please refer this. In case of any issue, please let me know http://www.dlink.co.in/Upload/UploadDownload/DSL-2640T.pdf

Sorry i tried to open 192.168.0.50 and it could not display. what is the new IP

* Visit support.dlink.com

- Make sure that you choose the right product on the site
- Download the Configuration Utility 1.00 for your D-LINK DSL 302 G modem
- Install to the computer then just follow the instructions

*Sorry it doesn't have the emulator to follow the directions.

Most of DSL modems are connected to PC with USB cable...
n if ur server is connected with other pc on lan .. you can use internet sharing option available in winxp.

Following are the steps to enable Internetsharing for other pcs.


How to use Internet Connection Sharing loadTOCNode(2, 'summary'); To use Internet Connection Sharing to share your Internet connection, the host computer must have one network adapter that is configured to connect to the internal network, and one network adapter or modem that is configured to connect to the Internet.

On the host computer loadTOCNode(3, 'summary'); On the host computer, follow these steps to share the Internet connection:

1. Log on to the host computer as Administrator or as Owner.
2. Click Start, and then click Control Panel.
3. Click Network and Internet Connections.
4. Click Network Connections.
5. Right-click the connection that you use to connect to the Internet. For example, if you connect to the Internet by using a modem, right-click the connection that you want under Dial-up.
6. Click Properties.
7. Click the Advanced tab.
8. Under Internet Connection Sharing, select the Allow other network users to connect through this computer's Internet connection check box.
9. If you are sharing a dial-up Internet connection, select the Establish a dial-up connection whenever a computer on my network attempts to access the Internet check box if you want to permit your computer to automatically connect to the Internet.
10. Click OK. You receive the following message: When Internet Connection Sharing is enabled, your LAN adapter will be set to use IP
    address 192.168.0.1. Your computer may lose connectivity with other computers on
    your network. If these other computers have static IP addresses, it is a good idea to set them
    to obtain their IP addresses automatically. Are you sure you want to enable Internet
    Connection Sharing?
11. Click Yes.

The connection to the Internet is shared to other computers on the local area network (LAN). The network adapter that is connected to the LAN is configured with a static IP address of 192.168.0.1 and a subnet mask of 255.255.255.0

let me know if it helps.

best regards,

mohan, had some info from BSNL, you really should have an ADSL modem from them, which could be a modem router, check on that too.

I belive with this modem you will:
1.Access the interface, generally http://192.168.1.1/
2. Go to Advanced on the left.
3. Select WAN.
4. Now you may see several rows of info, look for the one that says PPPoE, and then click edit to the far right.
5. Select Next one time.
6. Here select "BRIDIGING".
7. Click next all the way to the end.
8. Reboot, after you clicked save of course.


This is how you bridge 98% of PPPoE providers with a similar paradign modem.

Of course the next device in line will have to provide your username and password for your DSL connection.


Hope this helps!

First I will need to know the type of ISP service you have, T1 - DSL - ADSL - CABLE - etc. And the connection type, STATIC IP - DYNAMIC IP - PPPOE - etc. BPCS