Question about Konica Minolta bizhub 250 All-In-One Laser Printer

2 Answers

Konica/Minolta biz 350 C2557 after replacing DV unit and drum F8

I replaced DV unit and drum for konica/monolta bizhub 350 ran F8 and when finished made a copy it jammed at fuser and came up with error C2557 and so I pulled out jam turned machine off and on and the error came up before warm up, but when I put the old DV unit and drum back in copier the error goes away and it makes copies just fine. I also put in the new DV unit and drum in another machine and the error code persists in the other copier as well.  any suggestios?...

Posted by on

  • gmatthews_la Apr 22, 2009

    this is the 3rd dv unit i've gone thru.

  • Rawl Coulton
    Rawl Coulton Jul 29, 2015

    Problem is not DV unit. Toner supply solenoid is stuck. Disassemble toner drive unit and service/replace both bottle and feed solenoid. Warning: this is no easy job. You will have to manually replenish toner hopper then "help" the machine to recapture the gain setting.

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Konica Minolta Expert
  • 158 Answers

Tha minolta di3510 developer unit looks the same as the unit for the konica minolta bizhub 350 but the toner sensor in the minolta unit uses a different voltage range for the toner sensor and it will throw this code make sure you have the correct unit for this machine also you can try this
go back into tech rep mode and change these settings:
select tech rep choice mode
select printer tab
select atdc sensor gain
set the value to about 165
then back all the way out to the ready screen and power the machine off then back on and replenish toner in the user management screen.

Posted on Nov 05, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Contributor
  • 628 Answers

Obviously the dv unit is defective. Can you return it to the store for another?

Posted on Apr 22, 2009

  • Joe Fine Apr 22, 2009

    Are you sure you have the correct dv unit? It's odd that your machine and the others reject it.The other machine you mentioned--is it the same model?

×

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

hamzaskilltd

amir hamza

  • 318 Answers

SOURCE: Solution for error code c2557 konica minolta bizhub 250 machine

ADTC sensor failure

Posted on Aug 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Konica minolta bizhub 282 c2557 code appears after F8 ran and new related parts were replaced?


Did you replace the developer unit along with the new developer? mite have bad ATDC sensor bottom of developer unit

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Sep 21, 2016 | Konica Minolta bizhub Office Equipment &...

1 Answer

How to reset c2557


i put in a brand new developer unit, using the new developer I had just replaced into the old developer unit, reset drum and maintenance counters, ran F8 again. The machine came into ready, ran (1) copy, jamed on fuser entry and C2557 fired again. I then reset the switch in the back (right hand side), reset the switch on the main board, reset drum and maintenance counters, ran F8 again. The machine came into ready, ran (1) copy, jamed on fuser entry and C2557 fired again.

Aug 13, 2014 | Office Equipment & Supplies

1 Answer

Bizhub 350 error code c2557


Might want to have the developer replaced and drum/cleaning blade normally done all together, then run the F8 procedure and make sure the counters where cleared. Did you recently replace the drum and the developer if so did you clear the counters for the drum and developer, FIRST? IF not then the copier thinks the new drum and new developer are old. The copier works on the counters that is how it knows it got a new drum and developer. Get new developer and a new drum and have it installed correctly. Counters are clear before the unit is yanked out of the machine, then you remove the image unit/drum unit replace the developer/drum and cleaning blade. (DO NOT USE A VACUUM CLEANER WHEN REPLACING THE DEVELOPER static electricity can destroy the sensor located below the developer unit. Then reinstall and RUN F8. Make sure the fax line and Ethernet cable is removed can't print anything until the F8 is run. Or you will start all over again with new developer and a new drum.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Apr 22, 2014 | Konica Minolta bizhub C250 All-In-One...

1 Answer

Bizhub 350 printing blank copy


Does you machine say replace PC drum on the control panel if so need to have the drum developer replaced at the same time. The code is dealing with the image unit the drum is one part the developer section is the bottom part or the sensor at the bottom of the image unit is bad. If developer was replaced did that person use a vacuum clean if so then the static electricity from the vacuum clean destroyed the sensor. NEVER USE A VACUUM to remove old toner. Worse case the main board that the sensor feeds is bad. Also when (if the drum and developer where replace did that person clear the counter for developer and drum. Machine works on info from counters to set certain voltages on certain assy. If the counters are not cleared then the copier thinks there is old developer and old drum in the machine and sets voltages for those units when in reality there are new drum and developer . Also after the developer was replaced was the required F8 run. And no prints/fax or copies where made before the f8 was run. When replacing the developer and drum the fax line and the Ethernet cable need to be removed first even used F8 and counters are done in service mode.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Mar 05, 2014 | Konica Minolta bizhub 350 All-In-One Laser...

1 Answer

What part of the machine is affected in error code C2557 of Konica Minolta bizhub 350


Sir/Mam, Might want to have the developer replaced and drum/cleaning blade normally done all together, then run the F8 procedure/Developer Charge, and make sure the counters where cleared. Did you recently replace the drum and the developer if so did you clear the counters for the drum and developer, FIRST? IF not then the copier thinks the new drum and new developer are old. The copier works on the counters that is how it knows it got a new drum and developer. Get new developer and a new drum and have it installed correctly. Counters are clear before the unit is yanked out of the machine, then you remove the image unit/drum unit replace the developer/drum and cleaning blade. (DO NOT USE A VACUUM CLEANER WHEN REPLACING THE DEVELOPER static electricity can destroy the sensor located below the developer unit. Then reinstall and RUN F8/Developer Charge. Make sure the fax line and Ethernet cable is removed can't print anything until the F8 is run. Or you will start all over again with new developer and a new drum.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Jan 16, 2014 | Konica Minolta bizhub C250 All-In-One...

1 Answer

Ican't run F8 because of error C2557


Error c2557 means ATDC sensor abnormality.Most probably the developer is very low or weak in such condition.Check the developer.You can also increase ATDC GAIN in technical representative mode in order to get rid of this problem.
Also check the PC life/consumables life in "Counter"---"Special Parts life counter".Check if the life of PC Drum is 100% or near to 100 ten clear its value by pressing "C" button.Clear all counters to zero value.Now restart the machine and run F8.It will run smoothly.If you are replacing new developer then there would be no problem with it.

Jun 02, 2012 | Konica Minolta bizhub 350 All-In-One Laser...

1 Answer

Bizhub konica minolta 200 error code c2557


Does the control panel say replace PC drum? You need to have the Drum/Developer and the Developing unit replaced. Make sure that the counters are cleared before removing the old unit and make sure F8 is run after the new image unit is installed

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Apr 23, 2012 | Minolta bizhub 200 All-In-One Printer

3 Answers

Bizhub 350 error code c2557, how can i fix this?


This code happens if you replace drum without replacing developer. Both must be replaced at same time.

Sep 30, 2009 | Konica Minolta bizhub 350 All-In-One Laser...

6 Answers

Our bizhub-250 receives a C2557, need help with service mode


Utility/Counter -> Details -> [STOP][0][0][STOP][0][1]
Go to counter and clear the life of the developer and drums and then run F8 from functions.

Reset your Toners and Imaging units for Minolta Bizhub and CF series.
http://www.chipreset.eu

Jan 11, 2009 | Konica Minolta bizhub 250 All-In-One Laser...

Not finding what you are looking for?
Konica Minolta bizhub 250 All-In-One Laser Printer Logo

2,355 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6862 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

carpediemweb

Level 1 Expert

51 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...