My passenger seat will not slide back all the way in my 2009 VW gti

all modern cars are 180 to 200f. the service manuals cover this.
but no year car told
no country told
so can;t read it to you.
in AFRICA?

MY ONLY GOOD CLUE IS BELOW. WIKI + 1.4L NOT SOLD ELSEWHERE.


From 1984 to 2009, Volkswagen of South Africa manufactured two variants of the Mk1 Golf;
The 2007 VW South Africa Citi Golf range starts with a standard Citi Golf, in either 1.4 or 1.6 litre fuel injected models.
The 2009 VW South Africa Citi Golf range consisted of four new models:

• CitiRox 1.4i and 1.6i
• CitiSport 1.4i and 1.6i
• TenaCiti 1.4i
• CitiStorm 1.4i

GLOBAL GOLF SKIPS 1.4 SEE? AS DID USA.

• 1.1L 50 PS (37 kW) I4
• 1.1L 60 PS (44 kW) I4
• 1.3L 50 PS (37 kW) I4
• 1.5L 70 PS (51 kW) I4
• 1.6L 75 PS (55 kW) I4
• 1.6L 110 PS (81 kW) EG I4 (GTI)
• 1.8L 112 PS (82 kW) DX I4 (GTI/GLI)

Question moved from Spanish car maker 'Seat' to Volkswagen Jetta.

Volkswagen Jetta (2006) - fuse box diagram - Auto Genius

https://www.autogenius.info > volkswagen-jetta-2006-f...
Sept 23, 2019 - Instrument panel ; 32, Fuel Injectors (gasoline), 10 ; 32, ECM (diesel), 15 ; 33, Headlight washer system, 20 ; 34, Engine control elements, 10.

• 
  

  Volkswagen Jetta (2003 - 2009) - fuse box diagram - Auto ...

  https://www.autogenius.info > volkswagen-jetta-2003-2...
  Jan 28, 2020 - Volkswagen Jetta (2003 - 2009) - fuse box diagram. Year of production: 2003, 2004, 2005, 2006, 2007, 2008, 2009 ...

2006 Jetta Fuse Box Diagram in 2021 - Pinterest

https://www.pinterest.com > Vehicles > Cars
2006 Jetta Fuse Box Diagram Volkswagen Jetta 2008, Vw Jetta Tdi, Jetta Wagon,. T. Tyrese. More information. Volkswagen Jetta 2008 · Vw Jetta Tdi.

Look for a broken power feed going to the ECM.

try sliding seat all the way forward and then back then try pulling the handle to recline

Could be a bad ground. They are brown on v dubs.

call a lock smith

Not sure about VW but most cars with this type of warranty will have to be serviced annually by the supplier to qualify.

There is a small round metal wire that comes out of the front center of the seat. If you sit on the seat, while depressing the wire down, and pivot using your body weight, the seat should turn. Sometimes spraying the black seat mount is necessary to lube it. You may have to remove the seat if rusty or very dirty. To do that, slide the seat as far forward as possible, then lift the small metal lever on the left side of the seat, to release the lock on the track allowing the seat to move forward off the track. Note: both the passenger and drivers seats should turn on your model.

I just solved the problem for a stuck rear center seat belt in my 2002 Jetta.

Flip the base seat cushion forward against the front seat backs. Trace down along the belt to its tether point on the floor. The belt is sewn around a steel loop. The loop is anchored to a black steel hook. A thin silvery retainer plate is spring tensioned on top of the loop to prevent it from sliding off of the hook when the seat back is folded.

Therefore, you need to press the silvery retainer plate away from the hook (push up) to allow the loop to be slid from the hook. The belt was tight with the seat back in the upright position, so it was necessary to fold the seat back forward to create slack in the belt. Now push the belt loop towards the trunk and slide it off of the end of the hook (only possible with the retainer plate pushed up out of the way).

Now with total release of tension on the system via the bottom end of the seat belt being untethered and with the seat back returned to the upright position, normal extension and retraction of the belt will be reestablished. Next, simply extend the seat belt and slide the loop back into place over the floor hook. It snaps past the silvery retainer plate without all the effort required to hold the plate up during removal of the loop during disassembly.

Check again, the seat belt should be extending and retracting properly. Now just put the seat cushion back into regular position and you will be able to safely buckle up three people across the back seat.

It took about as long to do this repair as it has taken to post this answer to the problem. Note, the seat belt safety mechanism only allows normal extension and retraction of the belt when the seat back is upright.

you will need a metric rachet and wrench to remove 4 bolts from the bottom of of the seat. the bolts is bolting down the rail which the seat is riding on. to get to the front bolt you need to slide the seat all the way back and to get the rear bolts, slide the seat all the way forward.
I hope that help a bit