Printer will not pull in paper to be printed on.

hello,
have you fix the issue?I ve the same problem.
regard

Sebastiano

try unpluging the printer for few minutes

Leading cause of paper jams is debris/foreign objects that accidentally fell into the paper feed area. Please follow steps below to fix the problem:

1. Remove the sheets of paper from the feeder.

2. Grab a flashlight and look inside the feeder for any debris or foreign objects.

3. If you're willing and physically able, you may also turn the printer over. Any debris should just freely roll out from the feeder.

4. If feeder is clear, place the printer back on the table, open the printer cover and remove the cartridges.

5. Check the cartridge area for any obstructions/debris in the cartridge carrier's path or the paper path.

6. If cartridge area is clear, close the cover.

7. Re-brick your printer. Pull out the power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds.

8. When the printer turns on, reinsert the cartridges and load some paper. Try to print a document again to verify that the problem is fixed.

If problem continues, please contact Lexmark Technical Support Center for additional assistance.

try to look for the cassette it is located in the lower portion of the printer you can pull it to load paper

Unplug the printer from the power source to turn it off. Open the printer cover to access the cartridge area. If you see the paper jam, slowly and carefully pull the paper out of the printer. Avoid tearing the paper or avoid leaving torn pieces in the printer. This will cause future paper jams in the printer.
When all is clear, re-plug the printer into the power source. Load some paper and try to print again.

Unplug the printer from the power source to turn it off. Open the printer cover to access the cartridge area. If you see the paper jam, slowly and carefully pull the paper out of the printer. Avoid tearing the paper or avoid leaving torn pieces in the printer. This will cause future paper jams in the printer.

When all is clear, re-plug the printer into the power source. Load some paper and try to print again.
Tips: Use only paper that is in good condition. Fan the paper before loading into the feeder to prevent sticking together. Use the specified media type and sizes for your model. Don't overload the feeder.

You can access Canon online support info here. Enter paper jam as a search, then choose #4 to remove the obstruction.
Also see this:
Issue: Paper is jammed inside the printer
Solution: Removing paper jams MP600

Removing Obstructions or Jammed Paper If [Paper output slot - The paper is jammed. Clear the paper and press OK] appears on the LCD, follow this procedure to clear the paper jam Clearing paper jams from the auto sheet feeder (ASF) or paper output slot
Clearing paper jams inside the printer
Clearing credit card-sized or 4" x 6" paper jammed inside the printer

ASF / Paper Output Slot

1. Turn off the printer.
   
   
2. Remove paper from the ASF.
   
   
3. Gently pull the jammed paper out.
   
4. 1. If paper is visible from the ASF, use both hands to pull the paper out slowly.
      
   2. If paper is visible from the paper output slot, use both hands to pull the paper out slowly.
      
      The above illustration shows a PIXMA MP500.
      
      
5. If the paper tears and a piece of that remains inside the printer, open the scanning unit (printer cover) and remove the paper from inside the printer.
   
   Note:
   Be careful not to touch the components inside the printer.
   
   
   
6. Turn on the printer and confirm that the Alarm light is off.
   (If the jammed paper remains in the printer, the paper may be automatically ejected.)
   
   
7. Load paper back into the ASF.
   
   
8. Press <OK> to clear the message and continue printing. If you are printing from an application software, follow the instructions displayed on your computer.
   

Top
Paper jams inside the printer

1. Turn off the printer and disconnect the power cord and USB cable.
   
   
2. Remove the jammed paper slowly using the following procedure.
   
3. 1. Open the rear cover to check if the paper is jammed.
      
      
   2. Pull out the cassette and check if the paper is jammed inside the cassette area.
      
      
   3. Stand the printer with the left side down, holding the document cover.
      
   4. Press the tabs together and pull the green cover toward you.
      
   5. Check if the paper is jammed.
      (If you were not doing Duplex printing, you do not have to follow this procedure.)
      
      
   6. Close the green cover and place the printer back to a normal position.
      
4. Reconnect the power cord and power on the printer. Confirm the Alarm light is off.
   
   
5. Load paper back into the ASF or cassette.
   
   
6. Press <OK> to clear the message and continue printing. If you are printing from an application software, follow the instructions displayed on your computer.
   

Top

Clearing credit card-sized paper jammed inside the printer
Credit card-sized and 4" x 6" sized paper must be loaded properly. If this media is not loaded properly, it will feed into the printer and will not exit. Credit card-sized paper should only be loaded in the ASF and in portrait orientation. 4" x 6" sized paper can be loaded in the ASF or cassette. But must be loaded portrait orientation.
If credit card-sized paper was loaded in landscape orientation in the ASF and did not eject (exit), please follow this procedure.

1. Turn off the printer.
   
   
2. Load the same paper type that is jammed inside the printer in portrait orientation.
   
   
3. Power on the printer.
   The paper stock in the ASF will automatically feed the jammed paper from the printer.
   
   
4. To resume printing, load the paper in portrait orientation.

If 4" x 6" sized paper was loaded in landscape orientation in the cassette and did not eject (exit), please follow this procedure.

1. Turn off the printer.
   
   
2. Open the rear cover.
   
   
3. Fold in four a piece of letter-sized plain paper.
   
   
4. Push in the folded paper until it hits the jammed paper.
   
   
5. If the jammed paper is visible from inside the printer area, pull it out and proceed to step 7.
   
   
6. If the jammed paper cannot be pulled out, push in the folder paper from the rear so the jammed paper is in between the feed rollers.
   
   
7. Pull out the folded paper and close the rear cover.
   
   
8. Power on the printer and confirm that the Alarm light is off.
   The jammed paper should automatically eject.
   
   
9. To resume printing, load the paper in portrait orientation.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks

Thank you for contacting FixYa with your printer inquiry.
This is a common problem. The device can be set to print from tray 1 if it is loaded, or to print only from tray 1 if the type of media selected is other than standard bond.
Pull out tray 2 and make sure the paper size adjustments are properly set to match your size of paper. If you are using std bond and the adjustments are set to A-4 it won't pull paper.

HP Control Print Jobs Support Page: http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=115&prodSeriesId=1846088&prodTypeId=18972&objectID=c00764862
HP Support Page: http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c00764851&lang=en&cc=us&taskId=101&prodSeriesId=1846088&prodTypeId=18972
Hope this helps helps. Please keep us updated and remember to rate this answer.

Hi
Error 6A00
The 6A00 is a Canon generic code for paper path jam.

Solution 1:
Move the printhead carriage back and forth a few times.

Solution 2:
Check the purge unit: Moving the print head assembly will not clear a purge unit if its jammed with paper, paper clips, push pins, screws, cookie crisp, flower bud pods or the like.

Solution 3:
Press the ink pads down in the purge unit.

All I ask is please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

The problem is software rather than mechanical operation. Uninstall the printer driver from the Add/Remove section of the Control Panel. Pull out the USB port and replace it back. This will prompt you pc to install the driver of the newly found hardware. Reinstall the printer driver. Should your printer be observed to have the usual problem, replace both cartridges with a one. "Loading paper" problem feedback is the same prompt as what you get when cartridges are old or refilled with unauthentic ink.