Update my car stereo with new update - Pioneer AVIC-D2 In-dash Car Audio Stereo CD player with navigation and 6.5" video screen - Free UPS ... Car Video Player

If you are experiencing no audio output from your iPhone 12 Pro when paired with your Pioneer AVH2800bs, there are a few troubleshooting steps you can try:

1. Check the volume levels on both your phone and your car stereo. Ensure that the volume on your phone is turned up and that the volume on your car stereo is not muted or turned down too low.
2. Check your phone's audio output settings. Go to Settings > Sounds & Haptics and make sure that "Change with Buttons" is turned on. This will allow you to adjust the volume on your phone using the physical buttons on the side.
3. Try disconnecting and reconnecting your phone to the car stereo. Sometimes a simple disconnect and reconnect can fix the issue.
4. Check if your car stereo has any firmware updates available. Visit the Pioneer website and search for your specific model to see if any updates are available.
5. Try using a different audio cable to connect your phone to the car stereo. The cable may be faulty or damaged.

If none of these steps work, you may want to try resetting your phone's network settings or resetting your car stereo to its factory settings.

If you are using adapter, KS-PD100, it is possible that new iPods wont work with this older adapter, I would recommend to connect your iPhone via AUX on the front of the unit

Contact Hyundai Consumer Affairs for the radio code, and NEVER connect a phone to another device of ANY sort when doing updates.

No, other than a card or stick to put the update on. Instructions are on Kenwoods website.

Hello, be prepared to gasp. We know of factory updates costing $350 for Lincolns and accordingly cheaper for lesser Ford products. But is the Alpine a brand of stereo with Navigation or a car Model?

You can probably do an internet search under the topic "Navigation system updates" and plug in whether it is a car or stereo company.

the two componets r not compatible the stereo cannot read the type of program in ur ipod...i have the same prob with my home stereo an my ipod...u maybe able to have the stereo relearned by haveing the dealership install a new flash update into the stereo..if not i recommend replacement with a aftermarket stereo..

Software for car radio usually can't be updated. If Boss have a new firmwire, you can go to their website and install it via USB.

The Toyota Corolla has been around long enough that many owners find themselves needing to replace the factory stereo. Installing a new stereo in the Toyota Corolla gives improved sound and updated features. Swapping out the stereo in the Toyota Corolla takes basic tools and less than an hour. This article covers models from 1990 to 2000.

Open the hood and remove the negative battery cable from the terminal. Apply the parking brake and place the car in "D."

> Remove the trim from around the stereo by prying with your fingers at one corner. Some early models have two screws at the top of the trim piece to remove first. Allow the trim to hang on the drivers side of the dash if it's connected to the cigarette lighter.

> Locate and remove the four screws holding the stereo in place. Pull the radio out of the dash and disconnect the wires from the back of the head unit.

To install

> Connect the wiring harness adaptor to the original harness and let it hang from the dash. Slide the new stereo into the Toyota radio mounting kit, which is a thin metal cover and secure it per the manufacturer's instructions. Most adaptors have screws to hold the stereo in place, however some have clips, which engage automatically.
>Plug the wiring harness adaptor and antenna wire into the back of the new head unit and push the entire assembly into the dash. Reconnect the negative battery cable and turn the radio on.

> Ensure all of the stereo controls and speakers are working. Secure the radio in the dash with the original four screws and replace the trim.

Open the icon my computer in your desktop, double click drive c:, click the program files folder and locate the folder which contains stereo mix program.Look for the .exe file and click it. To place it back on the desktop, right click the .exe file and drag the new shortcut to the desktop

I bet updating the vehicle computer will provide no benefit
to a radio / stereo problem. If the stereo is a 2008 and there's
never been any service on it, there may be an internal memory
battery on the mainboard that has died. Higher function radios
have memory back-ups that retain user settings & instruction
sets. The fancier the features, the higher the likelihood. removing the fuse cuts ALL power to the stereo and forces
a re boot to the processor that runs all of it's functions.
leaving it fused but shut-off never turns it completely-off
and allows the system to get goofed up -
(without the back-up to retain things).
Just to find out will require removing the stereo from the car.
No dealership repairs stereos - search for DELCO car stereo
repairs shops to get an estimate, giving your symptoms.