Abit beep codes?

Hi I have 1 long beep and 1 long pause and it continues. thats with new ram in it .but it does work with the old ram

Check your codes here:
http://www.computerhope.com/beep.htm

Hi, you can download a manual here:

http://www.abit.com.tw/page/en/motherboard/motherboard_detail.php?pMODEL_NAME=AI7&fMTYPE=Socket 478&pPRODINFO=Manual

The fault could be the cpu, wrong type of ram, a faulty ram module
or a fault in the mainboard.
Check all the settings in the manual and the bios aswell.

Here is a list of beep codes:
Basic Beep Codes for ABIT AWARD BIOS Motherboards

1. No beep at all - this means your motherboard is dead, either due to a defective or underpowered power supply, poorly seated CPU or RAM, or a dead-on-arrival board
   
2. One beep - board is working fine
   
3. One long beep then machine shuts down - faulty, improperly installed or missing CPU
   
4. 1 short(Beep) System booting is normally
   
5. 2 short(Beep) CMOS setting error
   
6. 1 long - 1 short(Beep) DRAM ERROR
   
7. 1 long - 2 short(Beep) Display card or monitor connected error
   
8. 1 long - 3 short(Beep) Keyboard Error
   
9. 1 long - 9 short(Beep) ROM Error
   
10. Long(Beep) continuous DRAM isn't inserted correctly
    
11. Short(Beep) continuous POWER supply has a problem
    
12. A two-tone siren, generally caused by overheating or out of specification voltages
    
13. Four beeps then machine shuts down. This is because this version of the BIOS will shut down your machine if no fan tachometer signal is detected on the fan header. Make sure you attach a fan to the FAN1 or FAN4 header or clear CMOS to reset to default (no checking).

the beeps are post during post the very first work is done by the ram,all the memory in the ram is first transferred to the hard disk,and remains active untill turned off.
make sure that your RAM is securely seated
try replacing all the leads that attach to your hard drive including electrical extensions + IDE,SATA the ones that attach from your motherboard to hard drive
make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty or just replace them they are probably old and faulty ?
hope this helps

I still did not find beep code that match your problem..

Anyways here are the common beep codes for your motherboard.. it might help you too.
1. No beep - no reaction, the mother board is dead, power supply problem, processor and or ram problem.
2. 1beep - board is working fine.
3. One long beep then it shuts down - cpu problem, your processor is not working or missing.
4. 1short beep - system boots normally
5. 2short beeps - CMOS setting error.
6. 1long 1short beep - dram error
7. 1long 2 short beep - video card or monitor not connected
8. 1long 3 short beep - keyboard error.
9. 1long 9short beep - ROM error
10. Long beep - memory card is missing or not connected
11. Short beep - power supply error
12 Four beeps - there is no fan detected on Fan1 or Fan2 header. make sure to attach or reset CMOS bios to factory setting.


Hope this gave you an idea of your problem..

Much appreciated if you rate this help..thanks..

Sounds like memory. If you have more than one stick of memory, try using 1 stick at a time and see if it will boot.

More info here

http://www.computerhope.com/beep.htm

http://www.pantherproducts.co.uk/Articles/Motherboard/BIOSbeep.shtml

http://www.pcguide.com/ts/x/sys/beep/index.htm

http://www.computerhope.com/beep.htm

Hi had similar problem today, 1 long 4 short beeps - so not exactly the same.

I ended up resetting the CMOS - and this fixed my problem.

Hope that helps!

go into your bios and disable any kind of alarms related to your cpu or fans. hope this solves your problem.