Flashing code ee - Dometic 3109228.001 Duo Therm Comfort Control 5 Button

Still under Warranty then?

EE - There is a problem with the sensor terminals of the ice maker or the sensor circuit.

https://www.google.com/search?q=Midea+refrigerator+beeping+and+giving+an+EE+code

..

make model (what it is) is needed for all questions, or we have to guess!

The EE error code indicates an error on the main control board. This error code is usually fixed by unplugging the washer for 10 minutes to clear any memory errors on the control board.May 3, 2017

LG Front Load Washer EE Error Code - How To Repair?

..

the best suggestion is to contact the manufacturer at: (877)337-3639.

Water level alarm fault The alarm lamp will be flashed or display EE

your system might need reseting look for a reset switch on your thermostat or your inside unit usually means dirty filter

Check this against your code, but iff EE is flashing you may have an internal electrical fault that needs to be checked out by a repair person.

1. Frigidaire
   

2. GE
   

3. Panasonic
   

4. Sharp
   

5. Whirlpool
   

Sharp commercial grade microwave codes....
EE Mode Reason Action Required EE 1, EE 2 Magnetron failure

Call for service*
EE 3 Both magnetrons failed Call for service. EE 4 R-23GT, R-24GT and R-25JT only
Voltage too high Follow instructions on page 5 of Operation Manual under VOLTAGE SELECT to change from 208V to 230V. If problem is not corrected, call an electrician. EE 5 R-23GT, R-24GT and R-25JT only
Voltage too low Follow instructions on page 5 of Operation Manual under VOLTAGE SELECT to change from 230V to 208V. If problem is not corrected, call an electrician. EE 6, EE10, EE16 Thermistors failure Call for service. EE 7 Exhaust air temperature too high

Check that nothing is blocking air intake openings on oven back or that oven exterior is very hot. Correct. Wait a few minutes and try again. If problem persists, call for service.
EE 8 Circuit failure Call for service. EE 9 Maximum time is exceeded

Check page 11 in the Operation Manual. Touch STOP/CLEAR pad, and reprogram correctly.
EE 0 Fan lock error Call for service. EE17 Magnetron temperature too high

Touch STOP/CLEAR pad. Wait a few minutes and try again. If problem persists, call for service.

* EE 1 and EE 2: Can continue to use oven before service; however, check food carefully as additional cooking time will be needed.

Any time the EE is flashing, the servicer should be called. When EE is not flashing, check the reason and correct. Service is not necessary.

Hi.

EE means energy efficiency. hen EE is displayed there can be a defective thermistor or insufficient ventilation.

The following works on some A/C system: "When EE is displayed, press "energy save" and "zone control" simultaneously for about 5 secs"

Try also testing the system in auto mode, check ventilation and if possible test thermistor by reading impedance with a multimeter.

If when EE is displayed the unit also becomes non-responsive and does not turn off, then the problem may also be a defective controller board. Other parts, included the ones mentioned before, must be tested before replacing the control module.

Regards.

Ginko

EE
Remove your washer from the power source if you see an "EE" error code, where the first E is missing the top part of the letter. Your washing machine has a serious malfunction, and you must contact a technician.

A bit odd that as error code EE does not exist for washing machines, it's a refrigeration error code. Unless of course part of the display (led) has been damaged and the code isn't displayed properly.

Hope helps.

When EE:EE is displayed on remote control , press "Energy Save" &
"Zone Control" buttons simultaneously for longer than 3 secs. The error
code will then be displayed on the LCD.Thanks.