Hi, The dispenser flap on my Miele G575 dishwasher not infrequently fails to open at the correct part of the wash cycle. As a result the powerball detergent is not released and the wash needs to be repeated. Apart from that the unit works perfectly. Would a new dispenser solve the problem? Doccy D
If the water level is not adjusted at the right level
(see Miele G 575 manual page 29),
the flap doesn't open at the right circle,or doesn't open at all.
(Cause of the low water level the machine makes more noise!)
======Now shut down the power for the machine!!!=============
To adjust the water level new,you have to open the shield(2 screws) under the
main door.(enginen compartment).(You don't have to move the machine!)
On the right ,right,right,hand side,there is a 6 cm round beige plastic box.
(the first thing you see to you right and very easy access)
Only one black water hose(about 1cm=1/4inch) and a few wires are going into this box.
This is the water level adjustment box.
In the middle of the beige plastic box is a beige plastic screw
to adjust the water level new.Turning it clock vise ,increasing
the water level.
(For the right water level,see page 29 in your G575 Miele manual)
The water level hasn't to be super price.Just in about and enough.
(It seems that the rubber membrane in the water level unit ages
and therefor it has to be readjusted after a longer time)
Stop,stop stop!
I made a mistake.Don't touch the adjustment box.
99% reason why a Miele is not working properly anymore
is the water level.If the water level isn't reached the pump
is sucking air, therefor the water pressure is dropping down.
Without enough water pressure the flap won't open and
heat won't start.
The water passing resistance in your Miele increase by
the time because you have sediment in your water.Also
in the ionizing tank(salt water tank and resin filter)could built up after a longer
time alga which slow down the water pressure.
This is not a reason to throw your Miele away.
Miele are made to work 20 years.
Solution:You have to connect in your dial timer pole H6 with B6 with
a wire.
(You have two H6 pols and two B6 pols.)
(There's a wire plan inside the door.)
Don't do it if you can't do it properly!
Always shout down power by pulling the plug!
(to put the dial switch on 0 is not enough)
This wire connection is double the time in which water can flow into the machine.
My machine is now working like a new Miele.
I found this "trick" in a German forum.
You should also check the filter right in the beginning of
your Miele hose.Therefor you have to unscrew (by hand)the hose
from the house water tap.If you look inside the fresh water hose of your
Miele ,you can see a small filter for sand inside.
If it is dirty, you can pull it easily out with a pair of pliers.
Clean it and put it back.
Check at the same time the house water tap if it is giving still
enough water and pressure.The tape could be slowed down
by sediment over the years.
a kind of algues that increases
Sorry,I made again mistakes in my writing
and I don't know how to correct it.
Correction:"If the water level isn't high enough,the pump sucking air."
and instead of" hose water tab" I meant" faucet".
×
Watch also for how you load the upper rack. The flap opens inward and the rack has an opening to permit full opening. If this is blocked by your dishes, the flap won't open properly.
Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!
It could be jammed with old and hardened dishwasher detergent which dries like cement, preventing the little door from opening up. Clean the soap dispenser area with warm water and a toothbrush, especially underneath the area where the cover springs open.
It is caused by not enough water being allowed in by the 'flood protector'. You know, that weird lump on the inlet hose at the tap.
Mine has been slowly getting worse and worse. Seems it needs good water pressure to open the flap and it can't achieve it unless the correct amount of water is in the washer.
Currently I just chuck a couple of pans of water in at the start and again at 32 minutes for the rinse.
61,351 views
Usually answered in minutes!
I have a Miele G892 and I noticed for the first time that the soap dispenser never opened. Any ideas?
We have the same problem. Half the time the flap doesn't open and we have to re-run the load. The dishwasher has also gotten much noisier since the first few quiet months of operation. We're very disappointed in the product and the poor service we've received in trying to fix the problem. A repairman replaced the pump and motor but to no avail.
Dear all
Thank you for the tips. Below is the definitive solution!
We eventually had to have the Miele Service man out. The problem was
not with the door at all, but was caused by blockage of the water ducts
in the rotor. This resulted in eratic spinning and, apparently this
effects the door opening. Don't ask me how!! Anyhow, he cleaned the
rotor and, behold - problem solved. That was several weeks ago!
Doccy D
×