TECRA 9100 LED FLASHING 01001110

motor controller board has error comunicating with console, you can try to disconnect all leads connecting to console and reseat. failing that you would need to send off board for repair as new motor controller for next gen model is 700 gbp.

I found out on my H320 after i dismantled it , that one of the pins on the usb connector was loose and wasent soldered on the circuitboard , was also bended, the rest of the pins is also in bad condition seen from the outside, so check your usb connectors pins (frontside and backside), the optimal check is to open up the chassi to make sure that the soldered pins of the usb-connector are properly attached to the circuit board

Run the network setup wizard.

have a toshiba tekra 9100..the problem is that it when i turn it on it indicates that its on but the screen remains off when i try it after a while it manages to turn on bu wont boot sometimes it displaysi/o channel error or it sometimes gets past that but pauses when loading the o.s .what could be the solution for this problem

when you say cannot turn on cpu - what do you mean - ?
cannot boot up?
try removing the cmos battery for a minute then replace and try again.

any error beeps ?


working fine before ?

"F11" is a Serial Communications error between the Central Control Unit (CCU) and Motor Control Unit (MCU). The CCU is the main computer for the washer and is located directly behind the wash tub. The MCU is the Drive Motor Control board and is located in the rear of the washer adjacent to the Drive Motor on the left-hand side (facing from the rear with the back panel removed). The wiring harness can also cause the error, but it is not as common a problem.

Whirlpool is the manufacturer of both model washers and recommends the following troubleshooting advice. Remove the top panel of the washer by removing the three screws holding it in place in the rear. Once the screws are removed, the panel slides back, then off. Remove the rear panel of the washer for access to the drive motor and MCU. Now check the following:

- Check the wire harness connections between the CCU, the MCU and Drive Motor. Make sure all connections are attached and making good contact. Check for any broken wires or connector pins.
- Check the Drive Motor to see if it free spins and that the belt is still attached and not slipping. If the motor is seized, replace it. If the belt is broken or worn, replace it as well.
- Check the MCU. Connector 1 is the Serial Communications Link between the MCU and CCU. Connector 2 is the connector to the drive motor. Resistance checks across pins 1, 2, & 3 are the motor windings. Connector 3 is the power supply - 120VAC should be read across pins 1 and 2 with the door in the locked position. NOTE: The connectors are read 1, 2, and 3 from the bottom to the top with the MCU installed.
- Check the CCU. Verify connectors 7 and 11 are properly installed. Facing from the front of the washer, connector 7 is the 4th connector from the RIGHT along the front. This is MCU Power. Connector 11 is the Serial Communications link from the CCU to the MCU and is located along the left hand side of the CCU (the connectors are numbered 11 through 14 back to front).
- Check the Drive Motor. Remove the connector and perform resistance checks on the motor connector pins. Readings across pins 1 to 2, 2 to 3 and 1 to 3 should read 6 ohms.

In most cases this is an indication of a failed CCU. This is an easy repair that the average do-it-yourselfer can accomplish on their own. If the washer is still under a warranty, parts and labor would be covered. With no warranty, a replacement parts will vary in price depending on where you get them. There are several good websites available that you can order parts on line and have shipped directly to you.


NOTE: Remove all the connectors from the CCU ONE AT A TIME and reconnect to see if the error code goes away BEFORE you decide to purchase a new one. It is not common, but sometimes a flaky connection can generate error codes.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.%^&*

try to check the speakers or microphone lines and jacks whether they are connected properly . if still does not work, then check the audio settings under sound and devices in control panel.
If still makes no difference , then try reinstalling the audio drivers via the CD that was provided to you or u can find the drivers on http://www.toshiba.com or http://www.driverfiles.net/Notebooks/Toshiba/Tecra-9100/download/page,sh,31396,221,19,.html

seems like the mainboards are screwed

BUT

all is not lost

I Buy toshibas with this fault for my family and send them to a nice bloke (ex toshiba Tech ) who fixes them fo £45 I can get a good working lappy for 75 - 80 quid

search on ebay for Toshiba Tecra 9000 / 9100 laptop repairs

curent auction is 220452652232 @21july 09

i have a full set of drivers for this machine but not sure how i cud send to you.

Error 7 is a power related problem. This is what u need to do.
Remove back cover.
Plug in power when tv goes into error protection, check power supply and see how many times the led flashes. Right below the flashing green led there is a list 1-13 of error codes and what they mean. Your problem will probably be an error 7or 8 VSET or VSCAN . Which ever error code it gives you VA VSET or VSCAN or whatever it indicates look at the cable connectors to the power supply unplug that connector and the TV will stay on. And there will be your problem.