There are vents in the top of the oven door which allows grease,water etc, to go down inside the oven door. How can I take it apart to clean it>
Good Morning Suzi - Generally,
qualified technicians often perform complicated part replacement such as this,
however this may or may not be specifically for your model. Below are generic instructions
that I found on how to take your oven door apart to remove any stains that may
be caught down in the door vents.
Tools
needed: Phillips head screwdriver or small quad bit driver.
A. Open Door remove 2 screws and washers on door lining at door hinge area.
B. Refer to owners guide with door in broil stop position lift door assembly
off hinges.
C. Lay door on table, position so that handle hangs freely over edge of table
D. Remove 2 screws and washers that secure handle to lining assembly.
E. Remove 8 screws that attach textured steel door wrapper trim to lining
assembly 3 at top, 3 at bottom, 1 on each side
F. Lift door lining up and out of wrapper trim assembly.
G. Lay lining assembly on table with wool shield/inner part of lining facing
up.
H. Remove 2 glass clamps via 2 screws per clamp. These clamps attach innermost
clear glass to wool shield.
I. Lift out center clear glass from wool shield, this glass just lays onto the
wool shield and is held in place by the glass/ clamps in item H.
J. Clean each glass with appropriate cleaner, Windex, bon ami, fantastic, etc
K. One glass that remains in door lining assembly can at this time be cleaned
without further disassembly the lining assembly.
L. Reassemble in reverse order.
I hope this information helps to some degree.
Below are instructions on how to take your oven door apart to
remove any stains that may be caught down in the door vents. Tools needed: good Phillips head screwdriver or small quad bit
driver. B. With door in broil stop position lift door assembly off
hinges. C. Lay door on table, position so that handle hangs freely over
edge of table D. Remove 2 screws and washers that secure handle to lining
assembly. E. Remove 8 screws that attach textured steel door wrapper trim
to lining assembly 3 at top, 3 at bottom, 1 on each side F. Lift door lining up and out of wrapper trim assembly. G. Lay lining assembly on table with wool shield/inner part of
lining facing up. H. Remove 2 glass clamps via 2 screws per clamp. These clamps
attach innermost clear glass to wool shield. I. Lift out center clear glass from wool shield, this glass
just lays onto the wool shield and is held in place by the glass/ clamps in
item
H.
K. One glass that remains in door lining assembly can at this
time be cleaned without further disassembly the lining assembly. L. Reassemble in reverse order.
A. Open Door remove 2 screws and washers on door lining at door hinge area.
J. Clean each glass with appropriate cleaner, Windex, bon ami, fantastic, etc
SOURCE: Spills in between glasses of the oven door.
The door must be taken apart at least most of the way to clean glass. Just so you know, this is a problem with a LOT of the newer makes and models. If there are 2 screws behind the handle, take them out and some of them come apart enough to get your hand a paper towel in to clean. Otherwise, the door must be removed and completly diss-assembled.
SOURCE: Frigidaire Dble OVen Model FEB30T6DCC Stainless (electric
This exploded diagram of the door should help you get it apart,
It is going to be shrunk by the forum software, the full size image is
here http://www.easyapplianceparts.com/AdvancedModelSearch.aspx?ModelNum=FEB30T6DCC&mfgModelNum=&fkMfgID=4
along with a full list of parts should you need them
SOURCE: Burnt marks inside glass oven door
stain is between glass in oven door. can we take door apart
Below are instructions on how to take your oven door apart to
remove any stains that may be caught down in the door vents.
Tools needed: good Phillips head screwdriver or small quad bit
driver.
A. Open Door remove 2 screws and washers on door lining at door hinge area.
B. With door in broil stop position lift door assembly off
hinges.
C. Lay door on table, position so that handle hangs freely over
edge of table
D. Remove 2 screws and washers that secure handle to lining
assembly.
E. Remove 8 screws that attach textured steel door wrapper trim
to lining assembly 3 at top, 3 at bottom, 1 on each side
F. Lift door lining up and out of wrapper trim assembly.
G. Lay lining assembly on table with wool shield/inner part of
lining facing up.
H. Remove 2 glass clamps via 2 screws per clamp. These clamps
attach innermost clear glass to wool shield.
I. Lift out center clear glass from wool shield, this glass
just lays onto the wool shield and is held in place by the glass/ clamps in
item
H.
J. Clean each glass with appropriate cleaner, Windex, bon ami, fantastic, etc
K. One glass that remains in door lining assembly can at this
time be cleaned without further disassembly the lining assembly.
L. Reassemble in reverse order.
467 views
Usually answered in minutes!
×