Names what are pan, lan man,wan and please explain thanks

There are two halves to a router. The internet (WAN) side a local network (LAN) side.

The term WAN means Wide Area Network and generally refers to the internet.

The term LAN means Local Area Network. That would be for the computers that are in your office or home.

The LAN connects your computer to your printers or to other computers.

I hope that answers your question!

That is the name of the router. Default name is wireless.

http://support.dell.com/support/edocs/network/R48972/en/config/index.htm


SettingDefaultUser NameadminPasswordadminDevice Namemy.routerIP Address192.168.2.1Subnet Mask255.255.255.010/100 Ethernet LAN IP192.168.2.110 Mbps Ethernet WAN IP<obtain from ISP via DHCP>WAN DHCP ClientEnabledESSID (wireless network name)wirelessChannel6EncryptionNo EncryptionDHCP ServerEnabledNAT RoutingEnabled

http://technet.microsoft.com/en-us/library/cc958832.aspx
This link above explains subsets, a subset is the like this... 255.255.255.0 in the address coding as explained in the above... You need to change this

the default user name is admin, try that with no password.

if that doesn't work to reset it you

1- Power OFF your router.

2- Disconnect all LAN cables

3- Loop the WAN port to a LAN port, in other words hook up a network cable from the WAN port to one
of the LAN ports
4- Power up, wait 15 seconds

when you have done that use the default username and password to access the router, but when you have done this make sure you set a new user name and password and keep it somewhere safe.

Robert

Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then configure wan settings and lan settings enable wireless if you want to use wifi Then save settings and restart router Then connect cable from internet service provider to WAN port of router and connect ethenet lan cable from computer to lan port of router. . Let me know if you need further assistance. Thanks for using FixYa.

Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then configure wan settings and lan settings enable wireless if you want to use wifi Then save settings and restart router Then connect cable from internet service provider to WAN port of router and connect ethenet lan cable from computer to lan port of router. . Let me know if you need further assistance. Thanks for using FixYa.

Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then configure wan settings and lan settings enable wireless if you want to use wifi Then save settings and restart router Then connect cable from internet service provider to WAN port of router and connect ethenet lan cable from computer to lan port of router. . Let me know if you need further assistance. Thanks for using FixYa.

For that you need to check WAN settings and also make sure local ip settings gateway should be your router ip address. Make sure WAN settings are fine connect internet cable to WAN port of router. Then check. You can configure router with below method. Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then configure wan settings and lan settings enable wireless if you want to use wifi Then save settings and restart router Then connect cable from internet service provider to WAN port of router and connect ethenet lan cable from computer to lan port of router. . Let me know if you need further assistance. Thanks for using FixYa.

Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then configure wan settings and lan settings enable wireless if you want to use wifi Then save settings and restart router Then connect cable from internet service provider to WAN port of router and connect ethenet lan cable from computer to lan port of router. . Let me know if you need further assistance. Thanks for using FixYa.

run netstat on the lan pc to see if telnet server is listening on port 23. look at logs on the router and pc to see if it is blocking any traffic. make sure lan pc has route back to wan