Computers & Internet Logo

Related Topics:

Anonymous Posted on May 05, 2013

Model DX4300 Manual

Need to build

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Need a wiring diagram for a Gateway DX4300-03 system board

Need to know board model and those cases are wired so the plugs fit the original board. Your best bet would be to just get a new tower case. www.tigerdirect.com has them for $25

If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

1helpful
1answer

DX4300-05 How to open Gateway panels

1) Jaws of Life.

2) Acetylene torch

OH, I'M JUST KIDDIN'!

Gateway Support > DX4300 series of Desktop PC > Main Support page,

http://support.gateway.com/us/en/s/desktop/2009/gateway/dx/dx4300/DX4300nv.shtml

http://support.gateway.com/s/desktop/2009/gateway/dx/dx4300/DX4300rv.shtml

Looking at the Front of the computer, is how you determine Right side, and Left side.
The Right side removes with two screws, as far as I can see.

The Left side is a little harder to tell.

Gateway Support is of no help on this one. At least that I have found. Not in User Manual, because it's generic. One size fit's all.

However looking at the Rear View, it looks like the usual style to me.
Hard to make out though, because it's painted Black.

ON the back edge of the Left Side Panel, appears to be a Thumbscrew.
Even with centerline of Power Supply fan.

But there also appears to be a type of flip lock.
Or should state; push over to the inside; a little.

Then using the Fingerpull molded handle on the Left Side Panel, pull the side panel back.

Usually there are Slots in the metal frame, of the computer case.
The side panel has Tabs that stick out, with hooked end.
Along the top, and/or along the bottom.

You pull the side panel back until it stops, then move back forward about an inch, or so. Then bring the side panel straight out.

No?
Then post back what you see, and we'll try to figure it out together.

Post back in a Comment.

Regards,
joecoolvette
0helpful
1answer

Change the cmos battery in a gateway dx4300

Remove the case to see the CMOS battery, in most computers it will be a coin size 3 volt lithium battery type CR2032.
After installing a new battery go into the BIOS setting to set the Time and Date etc.
2helpful
1answer

My gateway dx4300-03 starts up fine and then about 5 minutes into working the monitor goes blank and the computer seems to go into sleep mode and won't restart until I unplug from the back and re plug in. ...

By Cyclontech!

Hi, The solution to fix the problem is by changing your power supply. Just make sure that you replace it with a 500W or higher and not with the same 300W which does not have enough power for this system, plus it is defective. I have changed the power supply to 4 diferent gateway PCs same model dx4300. And all 4 are working perfect. And run a check disk on CMD to fix the disk errors that were created every time you unplugged it and turned it on again.
0helpful
1answer

Need dx 430-15e manual

Would that be the Gateway DX4300-15E?

http://support.gateway.com/s/desktop/2009/gateway/dx/dx4300/DX4300nv.shtml

Left-click on User Guides, in the list.

Now Left-click on - Gateway Desktop User's Guide (In blue)

If you're looking for more detailed info, post in a Comment.
Not finding what you are looking for?

40 views

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

Brad Brown

Level 3 Expert

19187 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...