How do i get to the convergence screen withe universal remote

If the TV has been powered OFF by remote control for the last time, you can't turn it ON without a remote control after that. Without turn ON, and displays a screen, how you can enter a code or any thing to activate? Therefore, it will be best to buy its original remote control. Contact the authorized dealer for Avol.

Ur universal remote was able to move - + from the convergence grid wright,it is a good remote.The tv convergence board is dead.The tv convergence board the 2 STK convergence ICS and some or all of it resistors are dead too.These parts must be replaced on the tv convergence board to solved the tv pictures convergence problems.The shop,will cost u like $300-350 for parts and labors.

Adjust the convergence or reset it to factory default. Use only the remote when adjusting convergence. The front controls have no effect.

1. Press action button to enter MENU.
2. Navigate to SETUP.
3. Scroll down to CONVERGE.
4. Press VOL > to select.
5. Press CH buttons to navigate up or down.
6. Choose CONVERGENCE ADJ or RESET TO DEFAULT.
7. Press VOL > to select.
8. If CONVERGENCE ADJ is selected the align Green to Center screen will be displayed.
9. Use the navigation buttons on the remote control to align the horizontal and vertical green lines on screen, with the cabinet reference marks on top center and left
   center of cabinet.
10. Press ACTION button to display red center correction screen.
11. Use the navigation buttons on the remote control to align the red cross with the white cross pattern at the center of the screen. To prevent picture tube damage do not leave test pattern on for an extended period of time.
12. Press “0” on the remote control keypad to display the BLUE center correction screen, repeat procedure for adjusting blue. If needed press “0” again to return to RED correction screen. An adjusted cross pattern appears white with a minimum of color protrusion.

NINE POINT CONVERGENCE CORRECTION
Remote Control must be in TV mode.

1. Press ACTION button to display red correction screen.
2. Press the 1 through 9 keypad buttons on the remote control to select the desired convergence position.
3. Use the navigation buttons to align the RED cross with the white cross pattern.
4. Press “0” on the remote control keypad to display the BLUE correction screen, then repeat procedure.
5. To exit press ACTION button repeatedly, then press CH up.
   
6. 
   

1. 
   

Better off getting the original remote.
I never seen a universal remote that really did a universal job.

The cheapest place I found a remote for you is Remotes.com
They have one for $27.94
Just put in "NSLCD37" has the search.

I hope I answered your question. Please rate me. :)

I have a Dynex t.v, but my remot control doesn't work .

you will have to get a new mitsu remote in order to make the adjustment. Most universal remotes are made to just do basic functions, unless you start getting into nice sony touchscreen remotes but then they cost 100 by themselves.
the remote to a mitsubishi wd55513, wd65513 etc will also work on this set, I have done it before.
Here is one on ebay:
http://cgi.ebay.com/MITSUBISHI-TV-BIG-SCREEN-REMOTE-ORIGINAL_W0QQitemZ190275200565QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item190275200565&_trksid=p3286.c0.m14&_trkparms=72:1234|66:2|65:12|39:1|240:1318|301:0|293:1|294:50

The menu screen does not function the display. Without the original remote or a universal remote that does not have a display button, try unplugging the television for at least 2 minutes or more and plug the tv back in. This should reset the tv display. If the universal remote has a display button, depress the display button until you get the desired display results. Reference the user guide below for the display button.

JVC AV-36D503 36" TV - User Guide (page #43)

Without the original remote or a universal remote that does not have a display button, try unplugging the television for at least 2 minutes and plug the tv back in. This should reset the tv display. If the universal remote has a display button, depress the display button until you get the desired display results.

you will need the origional remote you can get one fast through this link just enter the model number www.replacementremotes.com
its normal after an IC change for the convergence to need adjusting, universal remotes can sometimes do it, but i have only seen that happen once or twice usually they wont have the right feature to adjust then save the settings.

I believe you can hit the menu button located on the front of the tv, scroll to the screen option, then always choose green convergence first, then the others. To make it easy on yourself, you could always purchase an inexpensive universal remote, or even better, an RCA remote.