Samsung SMH7159 Microwave Oven Logo

Related Topics:

joe young Posted on Oct 10, 2017

I have a panasonic microwave1250 watt ModelT945sfx. Does not work.Message shows door is not shut. The spring is good inside the door portion. if you slam it several times it might work. Manufacturer date is August, 2010. The last Panosonic lasted much longer. I think the door open button on the microwave is not operating properly or has weak spring

4 Related Answers

MicrowaveSvc

William Miller

  • 9179 Answers
  • Posted on Nov 17, 2007

SOURCE: Panasonic Microwave Turn table rotates when door is open

Found this Panasonic post in the Samsung section!

If it moves just a tiny bit when the door opens and then stops, that's normal.

If it keeps running when the door is open, that's usually due to a bad door switch or broken / loose door switch mount.

If you or a friend decide to look into it, we have critical safety information, info on door switch diagnosis and replacement, and
disassembly information at our site, linked here on Fixya: http://tinyurl.com/yzjozk

Any Panasonic parts not available locally can be had here: http://www.pasc.panasonic.com/epartr

We appreciate your thoughtful rating of our answer.

Ad
MicrowaveSvc

William Miller

  • 9179 Answers
  • Posted on Jun 08, 2008

SOURCE: Samsung Microwave Oven

Chances are you have a magnetron failing.

It's about time for the keypad to be going too, so unless it's a convection type or you;re really attached to it, it may time to retire it.

If you want to check into parts / pricing, see: http://www.samsungparts.com/search/search.asp

Anonymous

  • 1 Answer
  • Posted on Jan 28, 2010

SOURCE: micro wave shuts down in 3 seconds

I experienced the same problem with my GE Microwave (JVM1650SH02) shutting down in 3 seconds and then having to reset the time and date. The solution was to replace the Magnetron. I called GE (888-239-6832) for a free warranty part.
Once the part arrived, I removed the microwave from the wall and cabinet.
Once down, I removed the top and side panel off the microwave. I then unsrewed the metal side wall to get access to the magnetron. Lots of srews, so make sure you keep everything in order. Once the side plate was removed, you need to unsrew the 4 nuts on the outside of the magnetron, and also remove the unit next to the magnetron so you can get the magnetron out. replace magnetron and reassemble everything.

Good luck -

Anonymous

  • 4736 Answers
  • Posted on Feb 17, 2011

SOURCE: Samsung over the stove microwave, SMH8165B, 1 1/2

Unless, something has been mishandled the last 1 1/2 months you've had and been using the microwave, It sounds like a manufacturing defect. In which case, since it's only 1 1/2 months old, it's covered under warranty for repair or replacement by Samsung. Consult your Owners Manual about how to contact them concerning this. Keep in mind, you must still have your proof of purchase for the Warranty to be enforceable. If you don;t still have the sales receipt, your credit card statement showing the purchase may suffice.

Hope this helps you out.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My Panasonic microwave nn-t945sfx. Door is hard to shut and is not latching correctly. I inspected the spring and latch and it appears to be working correctly. I noticed the two holes where the latch

Common problem. Apply a small dab of lithium grease to the tips of the door hooks. You might also have to adt. the door latch switch assembly inside the oven as it could be bent out of shape from the hard to close door.
2helpful
2answers

Sharp r520kst door wont stay shut

If the door will not stay closed it is the spring inside door, or the small plastic piece that holds the spring which is attached to the $80.00 piece called outer door.
To fix it, it is EASY and you do not have to even take the inside cover all the way off. Just remove the three sides of cover by gently slipping a plastic putty knife around rim to release the clips. Then attach the spring to the small hole below where the plastic piece used to be, which is located in the metal on the glass frame piece, use tweezers, hold the other end of spring as you place spring onto plastic door latch and set into place!
Snap the inside cover back on and YAY! FINI!
2helpful
1answer

Panasonic inverter microwave: when i shut off the lid, turntale automatically rotating

When you close the door the turntable comes on? Almost all have a safety switch in the side of the wall where the door closes, An inspection inside the unit will show if switch is damaged or out of position which could cause this problem.
5helpful
2answers

Our panasonic inverter microwave (3 years old) needs repeated hard slams to shut the door so that the light goes off and the microwave will work. How do we fix this problem as I'm afraid we are going to...

We have a Panasonic Inverter microwave. Door became difficult to close and had to slam it hard while holding themicrowave to keep it from moving. When opening the door did not pop open but did unlatch. I ordered a new door lever from Panasonic. When got part I removed case from microwave and lever was okay. I then removed the perimeter strip on the inside of the door. With a screwdriver I stretched the spring at the bottom that keeps the door latches pulled downward. Spring still worked just not as stiff. Put perimeter piece back on the door and replaced housing (which I didn't need to remove in the first place), and then put a small drop of vegetable oil on the cams where the door latches hit when closing door. Viola, door opens and closed as new. Problem solved. Diagnosis: over time the latch tension spring hardens and gets too stiff. P.S.: I had several similar springs as backup in case I screwed up the original one.
6helpful
2answers

1200 watt panasonic, power on but will not perform

Hello :

This happens because of a bad door switch . The plastic mounts inside the microwave which hold the door switches and onto which the door latches lock when you close the door .

best regards .

please don't forget to rate !
0helpful
1answer

Panasonic - NN-T993SF 1350 watts microwave

Sorry this is something you wont fix at home I couldent even do this one.This is a nice unit depending on the cost this one I think is worth the repair bill , Good luck DFD please rate me TK U
3helpful
3answers

Panasonic microwave door is stuck. The door is not opening

If you push in on the open door button and it just goes in and does not open the door, then the problem is that the plastic piece that actually opens the door has broken. You can verify this by removing the cover from the microwave and look inside. If you are handy just buy the part from the panasonic parts store in your city and replace it. If not take it in and they will replace it for you.

Good luck

Tom
22helpful
5answers

Panasonic inverter door won't shut, light stays on.

Thanks for the tips - here is what I did (my wife calls me the Canadian McGuyver!) After taking off the plastic frame (using instructions in Solutions noted above) I used the metal part of a key ring and hooked one end to the spring and looped it around the thick finger/protrusion at the bottom. _197.jpg
Not finding what you are looking for?

131 views

Ask a Question

Usually answered in minutes!

Top Samsung Microwave Ovens Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

ExpressFiX
ExpressFiX

Level 2 Expert

691 Answers

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

Are you a Samsung Microwave Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...