Question about Bosch Classixx WFO 2866 Front Load Washer

1 Answer

Reset pcb bosch classixx 1200 express

Replaces brushes but machine doing nothing. Display showing single red line for 30 secs then goes blank. Resetting control board might help. How do I do this please?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Bosch Expert
  • 414 Answers

There is no reset as such, if the motor shorted when the motor brushes went there is a good chance that it blew the motor tracking or relay on the board. Sometime this is indicated by F20 or F21. Unfortunately this will be a new board. You could try to run a motor test as follows:
Hold in the start button while turning the dial one click to the left (30 easycare) wait until the display shows 888 or two indicators light up next to dial.
Release start and turn dial to 60 cotton (WITHOUT GOING THRO THE OFF).
Press start
This should start a motor test
slow turn one way, slow turn the other, pump on then up to full spin.
(some machines will show the rpm on the display).
If this does not work, you probably need to change the module aswell.
Best of luck

Posted on Mar 21, 2013

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
qpoint

qpoint

  • 69 Answers

SOURCE: where are the carbon brushes on a bosch classixx

Generally speaking, you might only expect to find carbon brushes in the motors used in some power tools. Household appliances use a different type of electric motor that does not use carbon brushes.

Posted on Aug 03, 2010

barkencoa

Barry Coates

  • 3463 Answers

SOURCE: Bosch Classixx 1200 Express wont spin!!!! HELP

Make sure that all the water has drained from the washer, if it has a filter, remove and clean, it is located behind a removable plastic panel at the front of the m/c, if it still does not spin, suggest you remove motor and check the brushes for wear, this is often the reason it won't spin, but will wash o/k.
Plz rate my solution.
Thanks

Posted on Dec 22, 2008

Anonymous

  • 1 Answer

SOURCE: Bosch classixx 6 1200 express has F17 on display

fault F17 error code appearing. What does this mean ? thanks

Posted on Jan 24, 2010

heatman101

D. Floyd Kolb

  • 43501 Answers

SOURCE: I have a Bosch Classixx

Hi,

F21 is a motor or control board fault.
This also can be caused by voltage spikes or surges...
To reset it.
Turn the appliance knob to the off or reset position, 12 o'clock.


Turn the knob to the 6 o'clock position.
Press and hold the spin button.


While holding it, turn the knob to the 7 o'clock position.
Continue holding the spin button for about 5 seconds.


Release the button.
Turn the knob to off.


When your turn it back on it should have cleared the error code

If the problem continues then check the motor...

heatman101

Posted on Nov 29, 2010

buckley119

  • 1 Answer

SOURCE: my bosch classixx 6, 1200 express washing machine keeps displayin

Bosch classixx 1200 express washing machine won't drain

Posted on Dec 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have accidentally put the child lock on my washing machine but have mislaid my instruction manual. Please help.


A re-posting of a Fixya answer:

1) Press the "menu" button until you see "CHILD LOCK :ON" appear in the display. ( if nothing is pressed within 10 sec.following this the menu will close and it will default to program in the display )

2) Once you see what I just mentioned in the display press the "select" button until "CHILD LOCK :OFF" appears in the display.

3) Finally by pressing the "start/pause" button the key symbol should disappear confirming you have successfully exited the child lock program.

Feb 23, 2018 | Bosch Washing Machines

1 Answer

All the lights on the spin speed panel light up and flash when switched on, no other sign of it starting a cycle, any clues please.


motor fault , change the carbon brushes and reset pcb. goggle e21 error its the same process to reset ..

Jan 29, 2015 | Bosch Washing Machines

1 Answer

F21 flashing on my bosch classixx 6 1200 express


F21 is a motor fault and in some cases can also involve a module fault. It could be as simple as the brushes need replacing or the drum has been severely out of balance.

Mar 21, 2013 | Bosch Washing Machines

1 Answer

Bosch classixx 1200 express lights flashing


Bosch 1200 classixx express washing machine. Upon switching on my machine, a little while later all of the lights on the control panel were flashing except the Start button. I tried to push the buttons but there was not the usual sound made upon depression of any of the buttons. They continued to flash. I switched the power off and cleaned out the pipes at the front of the machine to eliminate any obvious problems. Please help

Dec 05, 2011 | Bosch Washing Machines

1 Answer

Bosch classixx 6 1200 express is showing a key symbol in the LED - when I switch on the washing time goes back to 0 and the alert sounds and I cant start the wash I dont know how to switch the key...


Hello, welcome to FixYa.

The Key symbol means the lock has been activated some how.

On most bosch of your class this is how you work it on & off.

Here`s how to deactivate it...

1) Press the "menu" button until you see "CHILD LOCK :ON" appear in the display. ( if nothing is pressed within 10 sec.following this the menu will close and it will default to program in the display )

2) Once you see what I just mentioned in the display press the "select" button until "CHILD LOCK :OFF" appears in the display.

3) Finally by pressing the "start/pause" button the key symbol should disappear confirming you have successfully exited the child lock program.

Let me know if this was helpful to you or not, if so please take a second and rate it accordingly.

Thank you for visiting "fixya" for your washer solution inquiry.

good luck going forward.

macmarkus :)

Aug 19, 2010 | Bosch Washing Machines

2 Answers

Error code F 21


I have a Bosch Classixx 6 1200 express washing machine showing error code F21 on the display, what is it?

Apr 05, 2009 | Bosch Classixx WFO 2866 Front Load Washer

1 Answer

My bosch classixx 6, 1200 express washing machine keeps displayin


Bosch classixx 1200 express washing machine won't drain

Mar 29, 2009 | Bosch Washing Machines

1 Answer

Bosch Classixx 1200 Express wont spin!!!! HELP


Make sure that all the water has drained from the washer, if it has a filter, remove and clean, it is located behind a removable plastic panel at the front of the m/c, if it still does not spin, suggest you remove motor and check the brushes for wear, this is often the reason it won't spin, but will wash o/k.
Plz rate my solution.
Thanks

Dec 22, 2008 | Bosch Classixx WFC 2465 Front Load Washer

2 Answers

Changing the brushes when the motor is off


Remove belt, unscrew 2 bolts that hold the motor, unplug the motor connector, lever the motor back with a screwdriver. Check the motor brushes, if they are any shorter than 1 cm replace brushes.

Nov 16, 2008 | Bosch Classixx WFC 2465 Front Load Washer

Not finding what you are looking for?

Open Questions:

See all Bosch Classixx WFO 2866 Front Load Washer Questions

Bosch Classixx WFO 2866 Front Load Washer Logo

2,508 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

jimorris77

Level 3 Expert

411 Answers

Dw Wooten
Dw Wooten

Level 2 Expert

227 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...