H2 Blinking on the panel

There is a lock switch below the control panel. When the all-in-one is first shipped, there is a label that wraps over the switch and up to the control panel. When the label is gently pulled out, it moves the switch forward into the unlocked position.

The switch is below the area to the right of the frequently-dialed numbers short-cut buttons. To see a picture of the approximate location of the scanner lock, see page 2.3 of the MFP User Guide (this is page 29 of the PDF). The manual is available on the WorkCentre PE120/120i support page in the Documentation section: http://www.support.xerox.com/support/workcentre-pe120-pe120i/documentation/enus.html?operatingSystem=win10x64&fileLanguage=en . The direct link to the manual is currently http://www.support.xerox.com/support/workcentre-pe120-pe120i/file-redirect/enus.html?operatingSystem=win10x64&fileLanguage=en&contentId=53827 .

I hope this helps. If the scanner lock is in the unlocked position and you still get the error, then there is probably an internal problem. Whether this is a problem with the hardware or a sensor is unclear. If your unit is under warranty or covered by a service plan, contact Xerox or your printer/copier service provider.

Cindy Wells

WorkCentre 4250 Support - Xerox Support and Drivers

www.support.xerox.com/support/workcentre-4250/.../enus.html
XeroxProduct support for WorkCentre 4250. ... WorkCentre 4250 Support & Drivers. Fast Track to the Expert > Contact an experienced service technician ...

Hi,

Go to Start > Run, type in "services.msc", go down on the list till you see "Print Spooler", double-click, then click Start.

This should fix your issue.

hi enviro,

so its the supply inside the Xerox is the next to be checked or fuse too..a technician nearest you can help open it.

mastergani

Yes surely, only the power supply part of the printer is having problem, get it serviced by the technician.

When printing from the computer, Clicking starts from the printer before printing starts.

When the system was reinstalled, the proper printer drivers probably weren't installed. Unplug the printer from the computer. Go to Start -> Control Panel -> Printers. If your Photosmart 2610 is there, right-click on it and select 'Delete.' Allow it to remove all associated driver files. Run the printer's setup CD. If you don't have the driver CD, go to this link: http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?product=421139&lc=en&cc=us&dlc=en&lang=en&cc=us select your operating system and download the Full Feature Software and Drivers (hopefully you have a broadband connection). Run this setup program and follow all of the on-screen instructions. Do not plug your printer into the computer until instructed to during the installation.

This should resolve this problem. Happy printing!

Fuser Error, Open Heat
Error, Heating Error and
Overheat
There is a problem in the
fuser unit.
Unplug the power cord and plug it back in. If the
problem still persists, please call for service.

NOTE: Some Status codes will not clear even though the problem has been fixed. Status codes that will not clear must be manually reset using the 'Fault Reset 14 Procedure'.

1. Locate the [C] (Clear) button on the Control Panel, at the far right.
2. Locate the Image Quality button, below the Auto on the Control Panel, toward the left side.
3. Press the buttons in the following sequence within 4 seconds. Press [C] (Clear), press [Image Quality], press [C] (Clear) again, press [Image Quality] again.
4. The error code should disappear. If the Status code does not clear, repeat step 3 until the status code clears; but no more than five times.
5. Use the [10] and [1] buttons to enter 14 on the Display Screen, as if you were to make 14 copies.
6. Press the [Start] button. The machine should be ready to use.
7. Make a copy, to check that the machine is working properly

IF these steps do not work you will have to replace the fuser or fuser heat rod then perform the reset.

L6:The Main PWB sensed a Polygon motor lock signal error.

That is related to the mirror motor within the laser.
The laser most likely needs to be replaced.