Voltage Stabilizer for LCD TV

Voltage stabilizer that you are using is older. Voltage stabilizer that you are using is older. This problem is occurs cause of power fluctuation. Check the connections, Looking at the regulator from the face, the three terminals are V+ in, Ground (which is V- in and out) and the last one is V+ out. If it's backwards, it can indeed get hot. http://www.batterybhai.com/category/voltage-stabilizers/5

SUPRA 32 LED TV FULL HD Model No SLED32OT9001R

i nned by back light inveior borad how to by pleas send me web add and company detals

Please clarify by what you mean "voltage stabilizers".
Do you mean the power supply module?
Try EBAY, or www.shopjimmy.com

Basic troubleshooting guide here:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting
http://www.fixya.com/support/r7406380-tv_training_manuals
Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm/
Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague
Parts: www.shopjimmy.com
Parts: www.interliquidparts.com
Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps.
Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC series.

Not sure about a full blown voltage stabilizer being appropriate, A good quality surge arrester would help if there is a high level of spikes and surges on your mains - this may be what you meant.

They run at approx £30 and are built into a mains extension block. Last one I saw was from Belkin.

The PSU in the TV should work fine for a large variation in mains voltages.

They don't like repeated mains interruptions though.

SULKY CUT AWAY STABILIZERS

• Permanent Stabilizer
• Eliminates Pulled or Sagging Stitches
• Excellent Stretch Resistance
• Reliable; remains with fabric for continued stabilization through laundering and wearing
• SULKY WASH AWAY STABILIZERS
  • Temporary Stabilizer
  • Easy Removal with Water
  • Great Transfer Medium
  • Ideal when you do not want any stabilizer to show on top or bottom
  Sulky Solvy, Sulky Super Solvy, Sulky Ultra Solvy,
  Sulky Paper Solvy and Sulky Fabri-Solvy
  these are some examples u can take this from the market
  its a brand of america
  

Hi,

I only hope you have connected the tv with a stabilizer or is it inbuilt? This might be because of Voltage fluctutations. Also, check the connectivity of the internal power card.

Regards,
HP

You should have around 120-125 volts at the outlet. If you have less than 110 volts at that one outlet, you may need to have your house wiring checked. Go ahead and call your local power company and have the power coming into your house checked at their transformer. They should do this at no charge to you.

please give good rating if this helps


Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Stabilizer Bar Removal

1. Raise vehicle on a hoist. Refer to Section 00-02 .
   

1. Support vehicle with hoist or safety stands behind front sub-frame (5C145).
   

1. CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut, or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
   Remove and discard nuts retaining stabilizer bar link (5K484) assembly to front stabilizer bar (5482) and front shock absorber (18124) with an 8 mm closed-end wrench and an 18 mm open-end wrench.
   
   
   
   
   

1. Remove nuts retaining steering gear (3504) to front sub-frame, and move steering gear off the front sub-frame.
   

1. With another set of support safety stands under front sub-frame, remove two rear subframe retaining bolts. Lower rear of the front sub-frame to obtain access to stabilizer bar brackets (5486).
   
   
   
   
   

1. Remove front stabilizer bar U-bracket bolts and replacestabilizer bar brackets and/or front stabilizer bar as required. Discard lower suspension arm stabilizer bar insulator (5493) and bolts.
   

Installation

1. Clean front stabilizer bar to remove dirt and contamination in area of stabilizer bar insulator installation position.
   

1. Lubricate inside diameter of new lower suspension arm stabilizer bar insulator with Rubber Suspension Insulator Lube E25Y-19553-A or equivalent meeting Ford specification ESF-M99B112-A. Do not use any mineral or petroleum based lubricants as they will deteriorate the rubber lower suspension arm stabilizer bar insulators.
   

1. Install new lower suspension arm stabilizer bar insulators onto front stabilizer bar and position them in approximate location.
   

1. Install stabilizer bar bracket on front sub-frames and install new bolts. Tighten to 30-40 Nm (22-29 lb-ft).
   

1. Raise front sub-frame and install new front sub-frame-to-body retaining bolts. Position steering gear onto front sub-frame and install retaining nuts. Tighten to 115-135 Nm (85-99 lb-ft).
   

1. CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut, or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
   Install stabilizer bar link to front shock absorber and to front stabilizer bar, making sure that the stabilizer bar link is properly positioned. The letters "Top LH" and "Top RH" are moulded into the stabilizer bar link for correct assembly to the front shock absorber strut.
   

1. Install new nuts and secure stabilizer bar link assembly to front stabilizer bar and front shock absorber. Tighten to 77-103 Nm (57-75 lb-ft) at front shock absorber strut and 47-63 Nm (35-46 lb-ft) at front stabilizer bar.
   

1. Remove safety stands.
   

1. Lower vehicle.