Won't open The machine does not open when I press the open button to insert the cd even if the power is turned ON. I use the Remote Control and have replaced the batterries but wouldn't open. Anybody out there to help out? Thanks.

To reset a TV remote model TT-76, please follow these steps:
Remove the batteries from the remote control.Press and hold down any button on the remote control for about 5 seconds to discharge any remaining power.Release the button and then press and hold down the "Power" button on the remote control.While holding down the "Power" button, insert the batteries back into the remote control.Continue holding down the "Power" button for another 5 seconds.Release the "Power" button and then press the "Power" button again to turn on the remote control.The TV remote TT-76 should now be reset to its default settings.

Certainly! Here is a basic manual for the Aiwa CX-NA777:

1. Powering On and Off To turn the CX-NA777 on, press the Power button located on the top right of the system. To turn it off, press the same button again.
2. Changing the Volume Use the Volume control knob located on the front of the system to adjust the volume. Turn it clockwise to increase the volume and counterclockwise to decrease it.
3. Selecting a Source To select a source, such as the CD player or the radio, use the Function button located on the front of the system. Press it repeatedly until you reach the desired source.
4. Using the CD Player To use the CD player, press the CD button located on the front of the system. Insert a CD into the tray and press the Play button to start playing the CD.
5. Using the Radio To use the radio, select the Radio source using the Function button. Then use the Tuning knob to tune into the desired station. You can also use the Preset buttons to quickly access your favorite stations.
6. Using the Tape Deck To use the tape deck, select the Tape source using the Function button. Then insert a cassette tape into the deck and press the Play button to start playing it.
7. Adjusting the Sound To adjust the sound, use the Bass, Treble, and Balance controls located on the front of the system. These controls allow you to adjust the bass and treble levels, as well as the balance between the left and right speakers.
8. Using the Clock and Timer The CX-NA777 features a built-in clock and timer. To set the clock, press the Clock button and then use the Tuning knob to set the correct time. To set the timer, press the Timer button and then use the Tuning knob to set the desired start and end times.
9. Using the Remote Control The CX-NA777 comes with a remote control that allows you to control the system from a distance. The remote control features buttons for all of the main functions, including Power, Volume, Function, and CD playback.
10. Troubleshooting If you experience any issues with the CX-NA777, such as a CD that won't play or a radio that won't tune properly, consult the user manual for troubleshooting tips. You can also contact Aiwa customer support for further assistance.

Note: This is a basic manual and may not cover all features of the Aiwa CX-NA777. For more detailed instructions, please consult the user manual that came with your system.

Try reporgraming it

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.
4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes.

TV won't turn on • Press the TV button. Make sure the TV is plugged in.• Check the wall receptacle (or extension cord) to make sure it is "live" by plugging in something else.• Something might be wrong with your remote control. Press the POWER button on the front of the TV. If the TV turns on, check the remote control solutions on page 26.• The front panel controls may be locked (disabled). Use the remote control to unlock the front panel controls by selecting the Lock Fr. Panel in the PARENTAL CONTROL menu and press OK (box won't have check mark).Buttons don't work
• If you're using the remote control, press the TV button first to make sure the remote is in TV mode.• The front panel controls may be locked (disabled). Use the remote control to unlock the front panel controls by selecting the Lock Fr. Panel in the PARENTAL CONTROL menu and press OK (box won't have check mark).• Unplug the TV for two minutes and then plug it back in. Turn the TV on and try again.TV turns off unexpectedly • Sleep timer might have been activated. Go to page 24 for instructions.• KidPass might have been activated. Go to page 21 for instructions.• Wake-Up timer turned on the TV and no remote or front panel buttons were pressed for two hours.• Electronic protection circuit may have been activated because of a power surge. Wait 30 seconds and then
turn on again. If this happens frequently, the voltage in your house may be abnormally high or low.
• Unplug TV. Wait five minutes. Plug it in again.

See if your rams are inserted properly.

you will need to download the update from
http://pages.samsung.com/us/bluraysupport/support.html

how to - make an update CD

1. Download the software update file for your hardware.
2. If the update is compressed (zip file or rar file), the file should be uncompressed before burning.
3. You must burn the update file on a blank CD-R/W disc by using "Burn Image" option.
4. Burn an image file of the software update file (*.iso)

how to - update your player with your CD

1. Press OPEN/CLOSE to open the disc tray.
2. Insert the update CD-R disc with the software update, label facing up.
3. Press OPEN/CLOSE to close the disc tray.
4. Wait 1-2 minutes until the screen displays "Verifying Firmware version..."
5. After checking old and new version, select "Yes" or "No" with "?" or "?"
   on the remote control. If you select "No", BD-P1200 will be powered off in a state of tray open.
6. Press ENTER button on the remote control.
7. Remove the update CD from the tray.
8. Screen will display "Firmware Update Now Processing... Please do not turn off the power".
   This process will take 4-5 minutes. When done the screen and power will turn off automatically.
9. Turn the unit on again with the power button. They tray will close automatically and a
   Menu Language Selection screen will open.
10. Select the Language you want by pressing the corresponding number button.
11. Update is complete.

sit in car all doors closed put key in ignition and turn from OFF to ACC 3 times as fast as you can leaving it in ACC on the last cycle then press your remote button. your blinkers should flash to tell you this has worked.... may take you a couple of tries to get it!!

Step1There are a few ways to get your dvd/cd drive release itself. The first thing you should try is shut your equipment completely off for a couple of minutes allowing it to cool down. Once you turn it back on try to press the release button on your equipment. Step2If that does not work try to use a very thin flat tip screwdriver. Insert in on one of the sides of the dvd/cd drive and try to pull it out softly while pressing the eject button simultaneously. Do not force it out but give enough pressure while pressing the eject button. Step3More than likely inserting a screwdrive should release the dvd/cd drive. You can also try a butterknife as well just don't use to much force. Something else to check for is to make sure the power is acutally on for the device. If you are trying to open a drive that is not even on it will never open up for you.

TRY THIS Multi-Region:
1. Using the remote control, key in the following: 9, 4, Shuffle, Stop, Mute. 

To set a specific region:
1. Using the remote control, key in the following: Open (to open the tray - if already open, no need to press it), Stop, Shuffle, followed by the region number.
2. Press the Enter button on your remote control.