Question about GE Security Simon 3 Wireless Home Security System

2 Answers

Repair parts for simon 3

I need a new panal door switch mine is missing. Where can I buy one?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Try eBay. Look for any of the following keywords:

"GE Simon"
"ITI" (that's eye-tee-eye, for Interactive Technologies, Inc. original developer of Simon, now a subsidiary of GE Security)
"319.5" (the frequency on which simon sensors operate).

You'll find almost any sensor you can imagine there.

Posted on Jul 29, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 423 Answers

Type simon 3 accessories into google and you will find a billion places to buy accessories at.

Posted on Feb 15, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace passenger mirror


inside door should be small panal located about where the mirror is . remove it and disconnect power to mirror. remove screws or nuts whatever be the case.replace with the new one ...hope this help...before i forget if there is not a small panal then the door panal will have to be removed....hope this helps and if so please rate this post and good luck..

Aug 15, 2012 | 2007 Pontiac Montana

2 Answers

How to remove ford taurus window switch


remove screw on panal around handle that opens car. remove 2 screws underneath handle that pulls door closed. check around door panal edge for screws and if so remove them. Now remove panal by prying slightly around edges or panal as to pull the clips loose. Dont bother if some break,they can be easly replaced and dont cost much at all. I always use a still putty knife to help pry panal off. This insures you dont crack panal while pulling on it. Once thjis is dont you will have access to the switch...Simply replace it and place panal back on and HEY !! you did it..... hope this helps and if so Please leave rating on this post and good luck..

Aug 15, 2012 | 1998 Ford Taurus

1 Answer

1999 Chevrolet Silverado power windows, How do you remove drivers side door panel


not really sure on that one but on most first you will need to remove screw around handle that opens the door that needs to be removed. also should be screws underneth handle that pulls door shut that you will have to remove and in some cases . check around edge of door panal for more screws and if found remove them also. once all screws are removed you will need to pry on door panal slightly because there are clips behind panal holding it on. in alot of cases the clips break when removing panal but dont worry the can be bought at your local auto parts store and are very easy to replace. I usually use something flat like a small stiff putty knife to help pry door panal lose. this helps insure that you dont break of crack the panal. after all clips are off simply unplug wire connections and door handle linkage and your done. .....hope this helps and good luck

Aug 13, 2012 | 1999 Chevrolet Silverado 1500

1 Answer

The door does not lock. Can you buy a new lock


Hi
Yes you can buy either a new door catch or the interlock switch for under £10.
Try espares or barty spares on ebay.
Be careful if the door lock light is flashing as this could be the same problem as mine having replaced both items and the pcb control panel. It might be motor brushes causing a short in the pcb board awaiting answer from expert pcb is £100 brushes £15

HB

Dec 17, 2010 | Hotpoint WMA58 Front Load Washer

1 Answer

During spin cycle the washer allows water to enter the machine. If I shut the water during this cycle it spins out fine but when the cycle reaches the off position it doesn't really shut off. Sounds like...


open the door on the washer,in the middle rear just above the tub you will see the shute were the water comes in to the washer,make sure it is connected to the back panal,if is not than you will nead to remove the washer top door and cover assemble,there is a panal between the dryer and the washer,at the top of the panal on each side you will see a screw,remove them and remove the panal,at the back of the cover on each side you will see a clip with a 5/16 screw in it,remove the screws and slide the cover forward about 1 ",next lift the frount of the cover and on the right side you will see the door switch conneter,unhook the conneter and remove the cover,next you can see the water inlet shute,if is broken than replace it and hook it up to the back panal,next replace cover and panal and run a test run.

Jan 04, 2010 | Whirlpool LTE5243D Top Load Stacked...

1 Answer

My Whirlpool works in every way but will not spin.


sounds like a bad door switch,to replace the door switch you will nead to remove the body.first you nead to remove the two screws behind the control panal one on each side.next pull the panal forward and flip it up.next you nead to unhook the door switch.next you nead to remove the two s-clips one on each side.next you nead to pull the body forward and remove the body.now you con remove the two screws that holds the door switch on under the door next remove the door switch connecter from the body and install the new one.next reasemble unit

Dec 18, 2009 | Whirlpool LSB6200KQ Top Load Washer

1 Answer

Replace pasenger side mirror


it looks like you have to remove the door panal and unbolt the mirror and dissconect it, it should be the same, on pretty much all cars you have to remove the door panal to get to the mirror and it looks like cadillac hasn't changed much on stuff like this, they just chaged the look and style of the door panal, hope this helps any should be an easy fix but take your time and be easy with it, stuff can brake,good luck on your cadi, hope this helps you out. 

Jan 05, 2009 | 1994 Cadillac DeVille

1 Answer

Removal of door rt front door panal on a Ford Excersion


make sure to remove any screws or bolts and slide the panel up like when lifting someting and then remove the panel and unlpug any conectors behind the panel if necesary then put it bak the same way

Jun 01, 2008 | 2000 Ford Excursion

Not finding what you are looking for?
GE Security Simon 3 Wireless Home Security System Logo

Related Topics:

712 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Home Security Experts

Sean

Level 2 Expert

80 Answers

Bill

Level 1 Expert

39 Answers

Are you a GE Home Security Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...