WIFI error When I press the WIFI enable button I get 'WIFI Error press any button to continue' Please help!

Is the wifi enabled, can you see any wifi networks? If not, make sure wifi is enabled, if there is button on laptop to disable/enable wifi connections, swich wifi on.

Check from control panel -> network (network and sharing center in Vista/Win7) -> change adapter settings. If wireless lan adapter disabled (grayed out).

To clear the error, the procedure is as follows:
1. Turn off printer
2. Hold down MENU button on front panel and turn on power while continuing to hold.
3. Release button after 5 seconds (after the Please Wait message)
4. If error still occurs:
5. Press 91
6. If error still occurs:
7. Press 99

This should clear the error.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response
Thanks, Joe

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Pressing the keys Fn + F1 at the same time will enable or disable the built in wifi.

ERROR: Print Unable XX

The machine has a mechanical problem.
-OR-
A foreign object such as a clip or ripped paper is in the machine.


FIX 1: Open the scanner cover and look on the left, middle and right hand side under the covers for any foreign objects inside the machine. If the error message continues, disconnect the machine from the power source for several minutes then reconnect it.

FIX 2:
1. Unplug/disconnect the power cord from your printer.
2. Press Set button,while holding the Set button re-connect the power to your printer.
3. The Error code will be display "Machine Error 46."
4. If the Error code appear, press the "arrow up button"( ^ ) there will be numbers that are going to be display.
5. Choose 8 then press Set Button.
6. Press Arrow Up button again then Choose Zero (0) and press Set Button Again,now you will enter Service Mode.
8. Press "Mono Key/Button" 25 times or until "Purge Counter Appear."
9. Now press arrow up (^) again then choose "2" press Set Button.
10. Press Arrow Up (^) again then choose "7" press Set Button.
11. Press Arrow Up (^) again then choose "8" press Set Button.
12. Press Arrow Up (^) again then choose "3" press Set Button.
13. The purge counter will be reset to Zero.
14. Now Press Stop/Exit Button.
15. You will return to Machine Error 46.
16. Press Arrow Up (^) then choose 9 press Set Button.
17. Press Arrow Up (^) again then once more choose 9 press Set Button.
18. Your Printer will reset then wait until it power up again.


If all else fails, here is the User Manual with a troubleshooting section at the end:
http://welcome.solutions.brother.com/BSC/public/files/dlf/doc002376/cv_dcp145_asaoceeng_usr.pdf

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

If you are getting the error code concerning the baud rate.. You need to go into my computer, click on control panel, go into network and connections and delete my connection. This will take care of the error message then you can continue to connect your device to wifi.

Hope this helps

Specifically on the Magicolor 5430DL you can print when a cartridge is empty, but this is disabled by default. To enable printing even with a toner cartridge empty.Press the Menu Button, then press the right button until the ENGINE menu appears and press the select button.Next press the right button until TONER appears and press SelectOnce in the Toner Menu the first option should be "EMPTY" if not press the right button until you see "EMPTY" and press Select.There are two options, the default is "STOP" pressing the right button once should change from STOP to CONTINUE.While the display reads "CONTINUE" press Select.You should see the message "CONTINUE is selected"You can now print even when one or more cartridges are empty. However, the lack of the cartridge's color will be noticed in any print jobs calling for that color... (Obviously)

You didn't list your PC model or make, but it appears that you have enabled the network card to boot from it's rom chip. Turn that option off in your software or pcie Bios control.

Press and hold the VIDEO-1 button then press the SPEAKER A button and hold until "clear" is displayed. Then re-enter your setup menu, enable your surround speakers and if there is a decode priority select "PCM."

If your problems continue, contact Onkyo.