F1 error code on Kenmore Oasis He

It is either a bad control or a broken wire.


Oasis manaul

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

check if basket turns freely. if it does replace the main board

After replacing the part to fix the F1 code, the washer (Oasis he) now comes up with a HC code. Also, even though the cycle is set for warm/cold, the clothes are coming out hot at the end of the cycle...and the cold water is hooked up and on. Any suggestions?

The F1 error code on this washer indicates a Primary Control Board failure.



It is likely that the machine control board will need to be replaced to correct this problem.



The part number for the machine control board is undetermineable because you have not provided me with the exact model # of your washer.



The procedure for replacing the machine control board is provided HERE

LINK: http://media.fotki.com/1_p,wfgstgtftbtkrrdxgtqsskgwtqkq,vi/gfsfgfsgqxgfqtqtgwf/1/1303472/5961857/image55806img-or.gif



NOTE: Be sure to unplug the washer to disconnect electrical power before accessing internal components.



There is a slight possibility that a problem with the pressure switch hose could be causing this problem.

A pinched or twisted air hose can cause this fault code.

When you open the console, check the air hose connected to the pressure switch on the machine control board.

If it is pinched or crimped, I recommend rerouting the hose to resolve this problem.

This may fix your problem without replacing the control board.



NOTE: You may want to check for this condition before ordering the control board. Most electronic control boards cannot be returned for a refund or credit.



If you find no apparent problems with the air hose on the pressure switch, then replacing the machine control board on this washer should correct your problem. There is a risk involved in replacing this part yourself.

As noted above, you could have a problem with the air pressure hose that is not apparent upon your initial inspection. A service technician would normally need to properly and thoroughly diagnose this problem before replacing the control board.





Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

I think there might be a recall on your washer call to see. I am not for sure that there is a recall but I a m pretty sure there is. So don't quote me on that. the f1 error code usually means that you have a bad board. f1 means that your pressure switch line is failing and this is all in your board. check your owners manual if whirlpool is not going to pay for this repair sometimes there are extended warranties in your manual

The F1 error code on this washer indicates a Primary Control Board failure.



It is likely that the machine control board will need to be replaced to correct this problem.



The part number for the machine control board is undetermineable because you have not provided me with the exact model # of your washer.



The procedure for replacing the machine control board is provided HERE

LINK: http://media.fotki.com/1_p,wfgstgtftbtkrrdxgtqsskgwtqkq,vi/gfsfgfsgqxgfqtqtgwf/1/1303472/5961857/image55806img-or.gif



NOTE: Be sure to unplug the washer to disconnect electrical power before accessing internal components.



There is a slight possibility that a problem with the pressure switch hose could be causing this problem.

A pinched or twisted air hose can cause this fault code.

When you open the console, check the air hose connected to the pressure switch on the machine control board.

If it is pinched or crimped, I recommend rerouting the hose to resolve this problem.

This may fix your problem without replacing the control board.



NOTE: You may want to check for this condition before ordering the control board. Most electronic control boards cannot be returned for a refund or credit.



If you find no apparent problems with the air hose on the pressure switch, then replacing the machine control board on this washer should correct your problem. There is a risk involved in replacing this part yourself.

As noted above, you could have a problem with the air pressure hose that is not apparent upon your initial inspection. A service technician would normally need to properly and thoroughly diagnose this problem before replacing the control board.





Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

Per Sears. To fix the problem. Unplug the washer for at least 10 min then push pause or stop 2 times and this will fix the problem.

control bd under console bad

Ok these are not the series 70, getting a model number off the door will reallllllly help. Some of these sound like the oasis. F1 is motor control or primary control failure and F 41 is a rps thermistor failure.
For the guest with the 11027086601 kenmore elite oasis here is a link for supplying me with a partial model number, much thank yous!! paste in a browser:)

http://www.searspartsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?modelNumber=11027086601&productCategoryId=0153200&brandId=0583&modelName=RESIDENTIAL WASHER&diagramPageId=00002&componentDescription=CONTROL PANEL PARTS&documentId=K0601003&backToLink=Return to Sub Components list

I just finished installing my new control unit for my Kenmore Oasis and my F1 problems are GONE! I ordered it from Sears Direct Parts. With shipping and taxes it came out to about $174 for the part, but our issues are gone and now we can wash a load of clothes without having to reset it several times.