Jenn air range stove jsg8750 have a f1-7 error code

F0 is usually a stuck keypad button. Sometimes it's a problem with the wiring between the electronic oven control board and the keypad. With this model, it looks like the keypad and control board are sold as a single unit . See https://www.jennairreplacementparts.com/Shop-For-Parts/a13b103d563627/Model-JDS9860AAP-Jenn-Air-Range-Stove-Oven-Parts . You need the series 17 and later control board and timer, WP5760M302-60 . This part is roughly $400 from most vendors. https://www.partselect.com/Models/JDS9860AAP/Sections/CONTROL-PANEL-TOP-ASSEMBLY-AAP/?ModelID=91339&ModelNum=JDS9860AAP&mfgModelNum=&ManufactureID=1&Selected=53345&Position=3&mfg=Maytag&Type=Range&Mark=3 is another source.

I hope this helps.

Cindy Wells

Use a multi-meter to check the ohm's resistance of your temperature probe: should be 1100 ohms at room temperature = 72 degrees F. Range Stove Oven Temperature Sensor 12001655 Multimeter DM10T
After time, the connections between the temp. probe and the control board usually benefit from being disconnected and re-connected to keep corrosion from interfering with the resistance redings the control "sees" from the probe...

Did not find an error code "F1-8"
I did find these. Seems that about everything that can go wrong with a Jenn Air is related to the clock.


https://www.repairclinic.com/RepairHelp/FaultCodes/26/Range-Stove-Oven

Hi,

Below are the details of error code F9...

JENN AIR
'Newer Style' Range/Stove/Oven Fault Codes
Fault : F9
Condition: Door lock safety circuit on power relay board sensed
Replace power relay board

JENN AIR
Range/Stove/Oven Fault Codes
Fault:F9
Condition: Door latch supervisory
Check door lock circuit or replace clock assembly or ERC


Let us know if you want something else please accept the solution.

Thank You for contacting fixya.com

F1 - E1
EEPROM checksum error
1.
Disconnect power for at least 30 seconds.
2. Re-apply power and observe for
at least one minute.
3. If code re-appears, replace control board (also
called ERC or clock).

Note: Applies to all F1-E...
codes except F1-E3.

Read more: http://www.appliancepartspros.com/repairtips/repairtips_appliance+fault+codes.aspx#Jenn
Air Range / Stove / Oven Fault Codes#ixzz19GMNtS3r

http://www.appliancepartspros.com

JENN-AIR
'Newer Style' Range/Stove/Oven Fault Codes Failure
Code Condition Check/Repair F1 Power to element relay energized during time of day display Wiring harness shorted or change power relay board (PRB)

Note: for double ovens, change second oven board

JENN AIR
Range/Stove/Oven Fault Codes Failure
Code Condition Check/Repair F1 Defective touch pad or membrane Replace touch pad or membrane (this problem is usually the touch pad)

Having a problem with the stove on this Jenn Air svd48600b.
Often with the oven warms up to 350F it starts beeping at and shuts off.
It flashes either just an FC error code, or FC and F5.

It is often possible to get the oven to work again if you wait 10-15min and cycle the power.

I imagine something is wrong with a heat sensor? The temperature sensor responsible for displaying temperature on the control panel seems fine though.

One other detail, even when the oven doesn't shut off at hot temperatures, the fan comes on (at around 220F) and stays on for over an hour after the oven is turned off.

Does anyone know if there is a different temperature sensor that might cause this? Is there a specific electronics board that may be leading to this problem.
when it heats up.

replace the entire range: Jennair does not know how to design, make, or program electronics. It makes steel boxes that provide heat but electronics - that's not within their ability. Buy a Kenmore or a GE and your beeping problem will go away.

Hello welcome to fixya,


Below I pasted the fault codes for the two different years of this range.

To diagnose these difference you will need a hands on tech !
this is not an easy thing to determine

JENN AIR
Range/Stove/Oven Fault Codes
Failure
Code Condition Check/Repair F1 Defective touch pad or membrane Replace touch pad or membrane (this problem is usually the touch pad)

JENN-AIR
'Newer Style' Range/Stove/Oven Fault Codes

Failure
Code Condition Check/Repair F1 Power to element relay energized during time of day display Wiring harness shorted or change power relay board (PRB)

Note: for double ovens, change second oven board

if it is the stove that is in the picture the fault codes are in the door under the oven door.