Lexmark X544 standard bin is full

Hi,

I jsut followed the instruccion with a Lexmark X544 but i cant see the "Reset Maintenance Count". I could get de CONFIG MENU by holding the /check) and (right arrow). I move in the menu but none of the lines is anything related to "Reset Maintenance Count"

Hello,

This error is cause by either having your output paper bin full of paper or the flag sensor out of alignment where the paper comes out of the top. Look at the top f the printer where the paper comes out and you should see a black plastic sensor flag, it should move freely. If it is stuck remove the top cover above it and try to free it so it can move. Below is a picture of the printer with the output sensor flag circled.

Smash printer with axe or sledgehammer. Grin maniacally. After researching on internet,go out & buy new printer that allows you to print till empty & refill again! Obviously not a Lexmark...

Operation failed" is an error message that occurs when the phone has got a problem with it's GDFS. Your phone sounds like it's very poorly. You say you've tried a master reset? Can you tell me if that was reset settings or reset all? I had the same error message on my k850i when trying to get into my SMS inbox. A full master reset resolved it.Can I also ask that you remove the memory stick when you try a full reset and don't put it back in until you've tried the phone again?
You cannot get viruses on these phones, so we can safely rule that out.

Lexmark recognizes that some of our inkjet all-in-one customers may be experiencing issues with their print quality. We take our customer user experience very seriously, and we strive to ensure that each time a customer prints using a Lexmark device the page is crisp, clear and up to the highest standards.

However, if your device is displaying a 'printhead error' on the hardware and/or you are suddenly experiencing a print quality issue, please contact the Lexmark Technical Support Center at 1-800-539-6275 or point your browser to http://bit.ly/lFKDzs for online technical assistance.

SMTP is the outgoing mail server. If you're getting a error on the smtp gateway, please verify with email provider and check what is the correct outgoing mail server

For further assistance, please contact Lexmark Technical Support

what you need is a "FULL DUPLEX ASIO DRIVE",which you get with programs like cubase sx, this is like a universal driver which has always synced any audio equipment i've hooked up to my computer, internal & external.make sure it's the full duplex & not the asio4all v2.
But really you shouldn't be having much trouble if your using a USB midi interface.unless your computers sound card is ****.
try resetting the sound cards sample rate to 44100HZ which is the standard rate for most audio,or 48000HZ for digital.

Here's an article in the Lexmark website on A "Remove Paper - Standard Bin" or a "Std Bin Full error" Is Appearing on an E250d(n), E350d, E352dn, or E450dn Printer. Just click on this link: http://bit.ly/do0N3V. Read thoroughly and follow the instructions. Hope this helps. But if problem persists, I strongly suggest you contact Lexmark Technical Support to further investigate the problem. Thanks.

What your printer is telling you is that it thinks or knows that the top exit tray for the paper is full. This is the tray that is moulded into the top of the printer.

This caused by two things. It is actually full or the Bin Full Actuator is out of position and forcing the error condition.

Look at the standard bin. Over to the top at the top left corner there should be finger (almost the same as paper clip) hanging down. If it is not there, then it is more then likely that the finger is jammed up.

Don

The Standard Bin Full message is refering to the main output tray for the printer. If you have nothing mounted to the top of the printer, then the standard tray is where the paper is exiting.

What the message is telling you the bin is full and it is not, most likley the failure is that the sensor (a piece of wire is jammed in the up position. Just release the wire and let it hang down. That should clear your message and let you start printing again.

Don