Forgot my password for WBR-1310

If you already tried with username = admin password = blank "no password at all" or password = "password" then the only way to recover the router will be by doing a hard resset, (pressing the resset button in the back for 12 seconds) be careful you are going to set the router back to factory default and you will need to configure it again usually this is the only way to get the router back

reset the router to factory default. if you are confident. it is a small button at the back. press it coupel of sec then release. Then you can reset the password.

There are multiple versions of both of your routers, you can click on your version and try there tech info from there. If you have no luck, just post the right versions here and I'll see what I can do for you.

.............................................................................................................

There are multiple revisions of the WBR-1310, each with revision specific drivers, firmware, installation guides, and other resources.

• WBR-1310
• WBR-1310_REVB
• WBR-1310_REVD

There are multiple revisions of the WBR-2310, each with revision specific drivers, firmware, installation guides, and other resources.

Go to there support page and click on your model.

• WBR-2310
• WBR-2310_REVB

http://www.dlink.com/products/default.aspx?pid=WBR-2310&tab=3

What can I do if I forgot my password?
If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults.
To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty.

For the D-Link WR-1310, the following are the default login credentials:
username: admin
password: (none). Just leave it blank.

What password? Are you referring to the WEP or WPA-PSK password? If yes, I would like to inform you that no one could give you the exact WEP or WPA key. Even if you check the utility of the router.

What you need to do is to reset the router to factory default and then reconfigure the router. That's the only way that you could do in order to set a new password.

Have a good evening!

Go the router setup page, 192.168.0.1, type admin as the user name and password as the password (default, if you have changed these use your login info).
Then on the wireless page change the SSID (router name).
You can also add a security key on this page.

http://support.dlink.com/emulators/wbr1310_revA/wireless.htm

more info from D-Link:

http://www.dlink.com/products/support.asp?pid=474&pv=96&sec=1

Click on this link or copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Try with username = admin and password = blank "no password at all" or password = "password" then the only way to recover the router will be by doing a hard re-set, (pressing the re-set button in the back for 10 seconds) be careful you are going to set the router back to factory default and you will need to configure it again usually this is the only way to get the router back

Hi there,

As an initial info try to do a hard reset on the unit, this process will restore the system into a original settings. you can find the reset switch on either on the left of right sight of your router.

or

you may visit this SITE to recover again your current password without erasing or removing the current settings made.

Reset Password.

Hope this idea helps you.

Thank you for using fixya.

The username is admin
There is no password