My tevion universal 8 in 1 remote won't work any tevion devices

Hi Kym-
Without knowing what model "TEVION" VCR/DVD player you have, I found this link on ebay regarding original and replacement TEVION remote controls.
https://www.ebay.com/sch/i.html?_nkw=tevion+remote+dvd&ul_noapp=true

Hope this helps.

HI,
The One For All 3 Device Universal Remote Control is preprogrammed at the factory to operate an RCA TV, a Toshiba DVD player, and a Motorola cable box. To control devices other than the default brands, perform the following steps; otherwise skip this section:

HOW TO PROGRAM

1.Turn on a desired device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc)

NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step.

( CHECK THE BELLOW ADDED LINK TO FIND THE CODE )


2.On the remote control, press a device key once (i.e., DVD/VCR, CBL/SAT, or TV).

NOTE: To program control of a VCR, PVR (or DVR), TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCRonce. After programming a VCR Combo device, you will be able to control channel selection, volume, and VCR functions.
NOTE: To program control of a DVD Player, DVD Player/VCR Combo, or TV/DVD Player Combo, press DVD/VCRonce. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.
NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR) Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR) Combo, press CBL/SATonce.

3. Press and hold SET until the LED (red light) blinks twice, then release SET

4. Use the Manufacturer's Codes (starting on page 18) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.

NOTE: If the LEDdid not blink twice, repeat steps 2 through 4 and enter the same code again.

5.Aim the remote control at the device and press POWER once. The device should turn off.
If it does not, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still doesn't work, try Searching For next code.

NOTE: If the device does not have a POWER key, press PLAY

6. Repeat steps 1 through 5 for each device you want to control. For future reference, write down each working device code following.

Electronics Equipment Repair Center ONE FOR ALL URC3021 UNIVERSAL REMOTE...
Electronics Equipment Repair Center ONE FOR ALL URC3021 UNIVERSAL REMOTE...

To program the remote, press and hold the TV button. Then enter the 2 digit code from the code list. The EUR7724KC0 will only control TVs from about 17 manufacturers that were manufactured before the remote was programmed. If the given code for the TV brand doesn't work or the manufacturer isn't listed, then the remote can't control that TV. I'll list a few of the codes (see the manual, link below, for more):
Panasonic 01, 02
RCA 03
Samsung 14

The EUR7724KC0 remote came with several devices including the PV-D4734S DVD/VCR. The directions for programming the TV code are on page 28 of that manual. The code list is on page 29. This manual is available from Panasonic here: http://service.us.panasonic.com/OPERMANPDF/PVD4734S.pdf . Since this particular DVD/VCR model was listed at Amazon in 2004, it probably won't work for TVs built in that year or later.

I hope this helps.

Cindy Wells

Hi, the codes you have requested;

Magnavox - 0054, 0706, 0030, 1454, 1254

Instructions to program code:

1. Turn on a desired device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc). NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step 2.

2. On the remote control,press a device key once (i.e., VCR/PVR, DVD, CBL/SAT,or TV).
NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press VCR/PVR once.After programming a VCR Combo device, you will be able to control channel selection, volume, and VCR functions. NOTE: To program control of a DVD Player,DVD Player/VCR Combo, or TV/DVD Player Combo, press DVD once.After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions. NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR) Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR) Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,then release SET.

4. Use the Manufacturer's Codes (starting on page 18) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly,
the LED will blink twice. NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter
the same code again.

5. Aim the remote control at the device and press POWER once.The device should turn off. If it does not, repeat steps 2 through 5, trying each code for your brand until you find one that works.

try 0000 that is always the default for everything i buy

u need to get a universal remote and a code book,then your most likely wont have any more problems

hi can anyone HELP I HAVE COBOLT JUMBO REMOTE BUT NO CODE FOR ACCER LCD

Check out eBay to see if someone has a remote for sale. This is not a name brand TV set, and therefore there is probably no support for service and parts.

If you decide to change TV sets, stay with the big name brands, and check them out for after sales support and service.

Jerry G.

u can download the manual in www.fascin8.co.uk

Original link no longer working. Found this: http://files.remotecentral.com/download/220/urc08-manual.zip.html
Comment if it's wrong one.