Not charging I connected the charger but not charging appearance in display

1. Check the phone or tablet, charger, and USB cable. Verify the phone, tablet, charger, and USB cable have no physical or liquid damage.
   Check the USB connections for corrosion and bent pins. Inspect the Liquid Damage Indicator (LDI). The LDI should be solid white, or white with pink or purple X's. The USB connection should be firm with very little mobility.
   Remove any cases or other accessories that may cover the charging port or buttons.
   
   1. Remove the battery (certain devices only). On devices with removable batteries, remove the battery for 60 seconds and then reinsert it.
      
   2. Charge the phone or tablet. Connect and charge the phone or tablet using the supplied charger for at least 1 hour.The battery charging indicator may take up to 10 minutes to appear on the display.
      
   3. Restart the phone or tablet. Disconnect the phone or tablet and then attempt to turn it on by holding the Power key (or Side key) and Volume down key for 15-20 seconds. The Samsung Galaxy logo will appear.
      

I think the problem is with your charger or cable. Charge with another charger and check or else give it to repair. Most probably charger may be upset

As I understand these kind of cameras does not charge when connected to a computer. You need a separate charger.
The A460 uses 2x Size-AA Alkaline or NiMH Batteries.

Sport mate, but it appears your device is communicating with you but you aren't decoding. *smiles*

First, you've got several problemchallenges all present in your device/tech gadget.

MTP- media transfer protocol...connected
USB connected.

To resolve, navigate your way to Settings/ developer options/USB debugging

Click on this and get the ? off, first.
Click again and get the ? back on.

Next, select from the displayed menu the option for USB charge only. EXIT.

Problem 1 solved.

Battery with red X marking on it while on display.
Battery is no longer considered GOOD? by your phone/tab.

Needs to be replaced.
Problem 2 solved.

Why Cellphone/tab not charging?
Check the recommended AC charger rating for your device/gadget, first.

Check the charger rating you've been using to see whether these values match.

Output DC=????
mAmps=????

Lastly, issue with Indpsert SIM card.
You need to confirm whether your cellphone/tab is locked to a particular Network carrier company or not.

If locked, you need to jailbreiak/unlock it.
Otherwise, a technician may have to check the SIM card terminals for you.

Hope these tips help. Feedback please. All the best.

First Option:
mostly nokia chargers doesn't make problems...
just try the following..
connect ur mobile with a system (usb cable)...
found out whether it is charging or not...
if the same prblm appears then there is a prblm in ur cell phone or power jack(socket)...
if it charged with usb cable buy a new charger
Please change Phone Bettery and check the charging
IF Charging Problem not Solved So


Second Option:
Your Phone charging IC Fault So Please change charging IC
And charging Problem will Solved Quickly

First Option:
mostly nokia chargers doesn't make problems...
just try the following..
connect ur mobile with a system (usb cable)...
found out whether it is charging or not...
if the same prblm appears then there is a prblm in ur cell phone or power jack(socket)...
if it charged with usb cable buy a new charger
Please change Phone Bettery and check the charging
IF Charging Problem not Solved So
Secend Option:
Your Phone charging IC Fault So Please change charging IC
And charging Problem will Solved Quickly

I learned that with the unit off - hold the on button down - don't release it. A PRE-BOOT MODE message will appear at the bottom and may flash. Continue holding down the start button. The first time I did it a series of dots came on the screen and I was instructed to touch each one. After that it started as normal. I plugged into a wall charger and but git the pc and nuvi icons again. I repeated the process - holding the on button on and let the PRE-BOOT MODE appear and kept holding but this time a different message came on and then the PRE-BOOT MODE appeared again. I let it go and took the unit to my car and plugged it into the Garmin car charger and it worked as it used to - normal. However, when I plugged it back in the house to the wall charged I got the pc and nuvi icon again. It appears that I am using the wrong wall charger as a previous writes stated. But the nuvi still worked in the car plugged into the nuvi charger. I hope this helps.

1. Turn iPhone off and turn it on again. Press and hold the Sleep/Wake button on top of iPhone for a few seconds until a red slider appears, and then slide the slider. Then press and hold the Sleep/Wake button until the Apple logo appears.
2. If that doesn't work, connect it to the iPhone charger and let it charge for at least 10 minutes. Note: iPhone 3G does not support FireWire and will not charge from any FireWire-based power source.
3. If that doesn't work, toggle the ringer switch to see if the unit vibrates. If it does, it could be that iPhone is getting power, but is not displaying any image. (see "Display has no backlight or dark screen" below for further troubleshooting.)
4. While connected to the iPhone charger, try to reset the iPhone. Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until either the Apple logo or battery symbol appears. If the battery symbol appears, continue to charge iPhone until it is fully charged.

If your camera appears to be in working order, your charger or the power outlet may have an issue.

With all connections intact,

1) Please try to connect the charger to a different power outlet and try again.

2) If the charger doesn't appear to show any indications of charging, try with a different charger.

3) If the charger works fine, there may be something wrong with the battery - or the camera. In such a case, please consult an authorised service center for a resolution.

Thanks!