Sysem will not remoot fast and properly

I am in agreement William.

What do the Radial Aluminum Electrolytic Capacitors look like?

http://capacitorlab.com/visible-failures/index.htm

http://www.youtube.com/watch?v=Lut7MX5Dd_A

http://support.asus.com/Download.aspx?SLanguage=en&m=P4SP-MX&p=1&os=

Post back in a Comment.

Regards,
joecoolvette

if you are referring to a format on your hard drive

You have to format a hard drive with a third party disk unless its a usb data drive
Restart your computer

During the boot process you will see on the screen to press a certain key to enter setup

Press and hold that key during the boot up process to enter BIOS then using the arrow keys scroll to advanced bios features press enter change your first boot device to cd press escape then press f10 to save to cmos restart

note this will erase you operating system you will have to have an operating system disk to load it onto you hard drive or create a partition to load another operating system

note after you have loaded the operating system you should go back and change the first boot device to failsafe or optimised defaults

after windows has loaded
your computer will automatically restart it might restart 2 times one to finish the installation
the next will be because the operating system is loaded and will boot from your cd

during the boot process you will see on the screen to press a certain key to enter setup
Press and hold that key during the boot up process to enter BIOS using the arrow keys load failsafe defaults or load optimized defaults press escape then press f10 to save to cmos to restart

The BIOS is AMI. Under ADVANCED SETUP:
The options listed for 1st,2nd ,3rd Boot device include:
IDE0 means Pri master
IDE1 means Pri slave
IDE2 means Sec master
IDE3 means Sec slave

Hope this helps you

or if you are using a USB
insert your usb drive
click start right click on my computer select open you should see your USB drive
right click then select format
another way is to control panel administrive tools,computer management disk management right click on your drive select format
hope this helps you

Hi,
System Disk means you need to have the OS Disk.
Like XP/Vista/Windows .
Install the OS and your PC runs.

Thanks for using FixYa.

Just boot from a Windows install disk (put the cd in, press the boot selection key and select the cd unit) and allow it to run: the first step in the process is selecting the drive (select C), the second one is formatting of the drive - select the regular one, not the quick. After that just pull out the Windows disk or let it continue.

If your computer has just been formatted, your computer might require you to insert the boot CD

to be able to run it. You might hence get the error message Disk Boot Failure- Insert disk and

press enter displayed on the screen every time you will try to run it. This might be linked

to:

* 1. The boot options not correctly set in BIOS
* 2. A non bootable CD is found in your CD drive
* 3. You do not possess any bootable device
* 4. You have installed a new hard disk
* 5. The hard disk is not properly plugged
* 6. Your system files have been infected

Get more help and information for Disk Boot Failure. Hope this helps you....

your hard disk is disconnecetedor loose . pls check the hard disk power cable & IDE or SATA cable. Then check BIOS hard disk detected or not if hard disk is not detected your hard disk is faulty.

Your boot sector is corrupted you need to install windows again from a bootable windows cd...

U do a flasing of ur BIOS, there will a jumper on the mother board, U can find it refering the manual of ur mother board, jst change the jumper to flash the BIOS, then try booting...

Dear Waqar Khurshid,
What model is your PC and you should do right now is to insert a Bootable CD and troubleshoot the sysem

After making 100% sure you have no diskette or CD in any drives the conclusion may well be that the disk is ruined. You ay try to boot from a diskette or CD and see if you can access the disk then. (see www.ultimatebootcd.com for instructions to make a boot CD) "The ultimate boot CD" has a few tools that might help you out. Since you can't boot you must make it on a different computer, though. You may also try to insert the disk in a diffe rent computer to see if it can be booted there. Also make sure all cables are properly connected.