Posted on Jan 19, 2009

GE JT912-30 single wall oven "help" with F7 - F0 error

GE folks,
I started with a F7 error message. This is what I have done
I turned power off at the circuit breaker removed ribbon cable, put in index card both sides of ribbon cable. Also, cleaned ribbon cable with eraser. Reinserted ribbon cable to ERC board. Flipped circuitbreaker several times to shock sysem. No good results F7 still reappears.
Tried to determine if touch membrane panel or ERC board. With power on disconnected ribbon cable F7 remained off but after several minutes an F0 error message came on. Is that because of the detached ribbon cable? Can I assume since the F7 did not come on the failure is in the membrane touch panel and not the ERC board? Your help is appreciated.

1 Answer

Anonymous

Contributor 1 Answer
Posted on Jan 22, 2009

Anonymous

Contributor

Joined: Jan 22, 2009

Answers

Questions

Helped

1701

Points

I have a double oven GE Profile. The error message FO appeared. I shut off the circuit breaker for 30 minutes or more and the oven works but without warning FO reappears. FO message means there is short in the clear Off touch button. The only solution replace the complete panel. My cost delivered $328. Ouch!

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

I have a GE double wall oven. I have a F7 errot on display. I unplugged the ribbon cable and shortly recieved a F0 error code on both the upper and lower side of the display. I replaced the ERC. it...

Hello,

The F7 error coode means either the ERC or touch pad is bad. Having already replaced the ERC,replace the touch pad(the part w/the ribbon cable)

Gene

Read full answer

Aug 04, 2011 • GE Ovens

2helpful

1answer

My GE Model JCTP18WA5WW IS FLASHING F7 AND THE TIMER CANOT BE SET,ALSO THE OVEN CANNOT BE TURNED ON.

Hi

Thanks for using FixYa. Error F7 on your GE oven means that the keypad is shorted or stuck and to resolve this issue you’ll have to replace the Electronic Range control (ERC).Please do rate the solution if the issue is resolved or post a comment for further assistance.

Thanks
Rylee

Read full answer

Jun 17, 2010 • GE 24" Built-in Single Electric Wall Oven...

3helpful

1answer

Error Codes F0 and F7 on G.E. Wall Oven

Hi,

F0 , F1 , F7 - Stuck keypad may mean relay is turned on.

Determine if problem is with the Key Panel or Control by:
1. Pushing CLEAR/OFF pad.
2. Disconnecting Ribbon Cable from control and waiting at least 32 seconds to see if Code recurs

If code recurs, problem is in the control. Replace control.

If code does not recur, problem is with the Key Panel.

You could have a Tech Sheet from :-

http://www.repairclinic.com/0078.asp

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Read full answer

Mar 02, 2010 • GE Ovens

0helpful

1answer

What is error message F7 mean in GE Wall Oven?

F7 A = Function pad button stuck or
B = Bad clock Unstick button or
Replace Electronic Range Control (ERC)

Read full answer

Jan 31, 2010 • GE Ovens

5helpful

1answer

GE Profile Performance Spectra Range error code F0

F0 - F1 - F7 Stuck keypad may mean relay is turned on. Determine if problem is with the Key Panel or Control by:
1. Pushing CLEAR/OFF pad.
2. Disconnecting Ribbon Cable from control and waiting at least 32 seconds to see if Code recurs

If code recurs, problem is in the control. Replace control.

If code does not recur, problem is with the Key Panel.

Read full answer

Jun 20, 2009 • GE JKS05 Electric Single Oven

1helpful

1answer

The oven controls are not working. then FO shows

If your appliance is newer than 1996 F0 error code is a stuck key pad .
To verify turn off power and access the control panel and remove the ribbon connector that goes from key pad to control board .
Now restore power.
If the F0 code goes away you'll have to replace the key pad .
If it stays it means the control board is bad.
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Read full answer

Jun 11, 2009 • GE 30" Built-In Single Electric Convection...

7helpful

3answers

F0 error code on GE wall oven

I had the same FO error. It turned out that the ribbon cable from the front panel was not making good contact where it mated with the circuit board. Remove ribbon cable and clean contacts on ribbon cable. Replace cable and problem should resolve.

Read full answer

Oct 13, 2008 • Ovens

0helpful

1answer

GE wall oven display say F7, Bake and alarm sounds

Hi,

F7 error code occures due to
A = Function pad button stuck or
B = Bad clock Unstick button or
Replace Electronic Range Control (ERC)

Replace the ERC there are ten screws 3 on each side and 4 on the control leave the hex screws alone all you need is a phillip screwdriver.
REMEMBER TO SHUT OFF THE POWER FIRST lift and fold out the control panel remove the ribbon cable and remove the four screws that hold the control board . replace control panel in reverse order.
Good Luck!!
Thanks

Read full answer

Aug 06, 2008 • GE JKP30WMWW 27" Built-in Single Electric...

1helpful

1answer

Error message...

The F7 is intended to indicate a stuck START key. However, a design defect may cause a false indication. This can be corrected by adding insulation to the ribbon cable. You can find detailed instructions at my web site. Follow this link:

http://fp1.centurytel.net/Powerman/Dreaded%20F7%20Problem.pdf

All of the above must be entered as the address on the same line.

I have now shared my solution with over 1350 folks and most report success. It is simple and free. Please let me know if it works for you too. You can contact me [email protected]

Read full answer

Nov 01, 2007 • GE JRS04 Electric Single Oven

13helpful

2answers

Ge wall oven display says F7

Your problem is most likely caused by a short between sections of the ribbon cable between the touchpanel and the electronic control. The solution is to insert a slip of paper between the sections where it exits the touch panel. See the attached photo. If you have a metal touchpanel, insert slips of paper on either side of the ribbon cable as well. CAUTION: Be certain to turn off the power to the oven before you poke your fingers in and around the touchpanel. My solution has worked for hundreds of folks. Don't worry about the paper burning. If you have questions, contact me at [email protected].

Read full answer

May 29, 2007 • GE JKP30WMWW 27" Built-in Single Electric...

Not finding what you are looking for?

View Most Popular

Profile JKP56 Electric Double Oven

Ovens

I have a GE double wall oven. I have a F7 errot on display. I unplugged the ribbon cable and shortly recieved a F0 error code on both the upper and lower side of the display. I replaced the ERC. it...

GE Ovens

1,711 views

Ask a Question

Usually answered in minutes!

Have a manual for GE Profile JKP56 Electric Double Oven? Or just drag it here!

Related Topics:

GE JT912-30 single wall oven "help" with F7 - F0 error